Could you debug HSRP for us? Thought DEBUG STANDBY should do it.
Cisco 7200/7500 with PA-2FEISL HSRP gets stuck in init state on PA-2FEISL module in 7200/7500. CSCdr01156 (registered customers only) software upgrade; see bug for revision details Reset the interface using the shutdown and no shutdown commands SB: Ethernet0 state Virgin -> Listen SB: Starting up hot standby process SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB: Ethernet0 state Listen -> Speak SB:Ethernet0 Hello out 192.168.72.20 Speak pri 100 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello out 192.168.72.20 Speak pri 100 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello out 192.168.72.20 Speak pri 100 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB: Ethernet0 state Speak -> Standby SB:Ethernet0 Hello out 192.168.72.20 Standby pri 100 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello out 192.168.72.20 Standby pri 100 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello out 192.168.72.20 Standby pri 100 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Active pri 90 hel 3 hol 10 ip 192.168.72.29 SB: Ethernet0 Coup out 192.168.72.20 Standby pri 100 hel 3 hol 10 ip 192.168.72.29 SB: Ethernet0 state Standby -> Active SB:Ethernet0 Hello out 192.168.72.20 Active pri 100 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Speak pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello out 192.168.72.20 Active pri 100 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello in 192.168.72.21 Speak pri 90 hel 3 hol 10 ip 192.168.72.29 SB:Ethernet0 Hello out 192.168.72.20 Active pri 100 hel 3 hol 10 ip 192.168.72.29 Martijn Jansen -----Oorspronkelijk bericht----- Van: Tim Champion [mailto:[EMAIL PROTECTED] Verzonden: maandag 28 juli 2003 13:35 Aan: [EMAIL PROTECTED] Onderwerp: HSRP + ARP Problem [7:73098] Bit of a strange one this. We have 2 7206 routers running HSRP that are support by our telecoms provider. The fast ethernet interface of each is connected into our 2950 along with a firewall. >From the switch, or firewall, I can ping either of the 'real' ip addresses but not the virtual address. I have used debug arp and seen the arp request go out for the virtual address (the telco has done the same and see's the request come in) but there is no reply. If we configure a static arp entry it all works fine. Anyone ever experienced anything like this??? Many thanks Tim Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73100&t=73098 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
