I tried it.In fact the flash in this faulty router
works nice in other 1603.Also I get the folowing erroe
when I am booting at rmon using either rommon1>boot
eprom: or rommon2>boot flash:
I even tried to clean the pins of the connector where
PCMCIA Card fots.However the situation remains the
same.
Thanks in advance.
*** BUS ERROR ***
access address = 0xd030001
program counter = 0x4010b50
status register = 0x2710
vbr at time of exception = 0x4000000
special status word = 0x006d
faulted cycle was a byte read
C1600 processor with 2048 Kbytes of main memory
a
rommon 1 > dev
Devices in device table:
id name
eprom: eprom
flash: PCMCIA slot 1
rommon 2 > eprom
monitor: command "eprom" not found
rommon 3 > boot eprom:
program load complete, entry point: 0x4018060, size:
0x1e1568
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and
Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-BOOT-R), Version
11.1(10)AA, EARLY DEPLOYMENT RELE
ASE SOFTWARE (fc1)
Copyright (c) 1986-1997 by cisco Systems, Inc.
Compiled Tue 18-Mar-97 14:01 by ccai
Image text-base: 0x04018060, data-base: 0x02005000
*** BUS ERROR ***
access address = 0xd030000
program counter = 0x410d684
status register = 0x2700
vbr at time of exception = 0x4000000
special status word = 0x006d
faulted cycle was a byte read
monitor: command "boot" aborted due to exception
rommon 4 >
--- Gary Crouch wrote: > if
you have a flash card remove and reseat it.
>
> >>> "Mr piyush shah"
> 07/29/03 04:33AM >>>
> Hi all
> I have Cisco 1603 router with 1 Ethernet,1 port BRI
> plus 1 T Serial interface which I was using to
> connect 2 Mbps Leased line .Receptly it started
> malfunctining with coutinious boot .The error ***BUS
> ERROR*** .The log captured on console is attached
> herewith .Can anybody pls help whether why is it so?
> It is even not allowing me to enter into Rmon mode
> by
> pressing Break Key.
>
> Thanks in advance
>
> *** BUS ERROR ***
> access address = 0xd030001
> program counter = 0x4010b50
> status register = 0x2710
> vbr at time of exception = 0x4000000
> special status word = 0x006d
> faulted cycle was a byte read
>
> Initializing the PIT timer ...
> Initializing the RAM vector table ...
> Initializing monitor variables ...
> Reset Cause: (SRST) software reset
> C1600 processor with 2048 Kbytes of main memory
>
> getdevnum warning: device "PCMCIA slot 1" has size
> of
> zero
> getdevnum warning: device "PCMCIA slot 1" has size
> of
> zero
> open: read error...requested 0x4 bytes, got 0x0
> trouble reading device magic number
> boot: cannot open "flash:"
> boot: cannot determine first file name on device
> "flash:"z
>
>
> System Bootstrap, Version 11.1(10)AA, EARLY
> DEPLOYMENT
> RELEASE SOFTWARE (fc1)
> Copyright (c) 1997 by cisco Systems, Inc.
>
> Sizing main memory ... found 0x00200000 bytes
> Testing lower main memory - data equals address
> Testing lower main memory - checkerboard
> Testing lower main memory - inverse checkerboard
> Checksumming Monitor image ...
> Initializing main memory ...
> Hardware rev is 0x2
> Sizing NVRAM ... found 0x2000 bytes
> Reading NVRAM ...
> Reading cookie ...
> Initializing the PCMCIA controller ...
>
>
>
>
>
________________________________________________________________________
> Send free SMS using the Yahoo! Messenger. Go to
> http://in.mobile.yahoo.com/new/pc/
> [EMAIL PROTECTED]
>
________________________________________________________________________
Send free SMS using the Yahoo! Messenger. Go to
http://in.mobile.yahoo.com/new/pc/
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=73267&t=73161
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
