get it to work with HDLC before trying frame relay, to eliminate frame config probs.
>>> Joseph Ezerski <[EMAIL PROTECTED]> 10/12 4:52 PM >>>
I have:
A 2610 with a WIC 1DSU-T1 (internal CSU/DSU)
A 1601 with a WIC 1DSU-T1. (internal CSU/DSU).
I created a T-1 crossover cable according to Cisco's specs.
I am trying to connect those two routers in a simulated frame relay
connection. I connected the crossover cable and configured my two routers
to accept frame signals. I was not successful. I config'd both routers to
have sub-interfaces with an IP address on the same subnet. I did set the
2610 to have internal clock source and I set the 1601 to clock source line.
I currently get LINE UP, PROTOCOL down on the major interface and DOWN-DOWN
on the subinterface. What is it that I am missing?
FROM 2610-->>>
Serial0/0 is up, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: Psuedo Frame Link
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 254/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY, loopback not set
Keepalive set (10 sec)
LMI enq sent 56, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down
LMI enq recvd 87, LMI stat sent 0, LMI upd sent 0
LMI DLCI 1023 LMI type is CISCO frame relay DTE
Broadcast queue 0/64, broadcasts sent/dropped 2/0, interface broadcasts 2
Last input 00:00:00, output 00:00:08, output hang never
Last clearing of "show interface" counters 00:09:34
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
88 packets input, 1427 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
14 input errors, 0 CRC, 14 frame, 0 overrun, 0 ignored, 0 abort
106 packets output, 3408 bytes, 0 underruns
0 output errors, 0 collisions, 17 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
*************************************************
(also from 2610)
interface Serial0/0
description Psuedo Frame Link
no ip address
encapsulation frame-relay
service-module t1 clock source internal
!
interface Serial0/0.10 point-to-point
description Pseudo Frame Link
ip address 192.168.0.2 255.255.255.0
frame-relay interface-dlci 16 protocol ip 192.168.0.1
***Note that the 1601 is configured almost exactly the same except that it
has an IP ADDR of 192.168.0.2 /24 but I did not include the running config
to save space.
Thanks in advance.
Joe
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
