Edward,
Do you also have inverse arp disabled at the hub router? If not this would
explain why the remotes/spokes are still getting the info dynamically. I
could be wrong... but I'm very often not right.
Cory
-----Original Message-----
From: George Zhang [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, October 25, 2000 9:20 PM
To: [EMAIL PROTECTED]
Subject: Re: Frame Relay Map Help
Try 'clear frame' on the spoke router, see if it still works. If that does
do it, save
the config and reload the spoke router.
George Zhang
Sam LI wrote:
> well, read that chapter carefully, I have difficult on understanding when
I
> first read it
>
> Sam Li
>
> ----- Original Message -----
> From: Ed Moss <[EMAIL PROTECTED]>
> Newsgroups: groupstudy.cisco
> To: <[EMAIL PROTECTED]>
> Sent: Tuesday, October 24, 2000 10:34 PM
> Subject: Frame Relay Map Help
>
> > I am working through Caslow's Bridges Router and Switches book and I am
> > trying to get a firm understanding of frame-relay.
> >
> > I have generally recreated the lab on page 126 with the minor changes of
> > adding another router and changing addresses. For those without the
book
> > (which is very good by the way) this is frame on physical interfaces in
a
> > hub and spoke configuration.
> >
> > The hub can ping all spokes, and each spoke can ping the hub. However,
> > spokes can not ping each other until the 'frame-relay map ip" statement
is
> > added to point to each spoke.
> >
> > Everything can now ping everything else. Now we save the configs and
> > reload.
> >
> > Since map statements have not been added on the spokes to point to the
hub
> > (since they were originally learned dynamically) I expect that dynamic
> > inverse arp to be disabled, and there will be no dynamic entries on the
> > spokes for the same protocol and the same dlci.
> >
> > This is not the case in my lab.... here is the relevant part of the
config
> > on one spoke, and the results of 'show frame-relay map'
> >
> > interface Serial1
> > ip address 192.168.14.2 255.255.255.0
> > encapsulation frame-relay
> > frame-relay map ip 192.168.14.3 201
> > frame-relay map ip 192.168.14.4 201
> > no frame-relay inverse-arp
> >
> > Router2#sho frame-relay map
> > Serial1 (up): ip 192.168.14.1 dlci 201(0xC9,0x3090), dynamic,
> > broadcast,, status defined, active
> > Serial1 (up): ip 192.168.14.3 dlci 201(0xC9,0x3090), static,
> > CISCO, status defined, active
> > Serial1 (up): ip 192.168.14.4 dlci 201(0xC9,0x3090), static,
> > CISCO, status defined, active
> >
> > Can someone explain why this is happening? (also explain how disabling
> > frame-realy inverse arp works since I get similar results).
> >
> > Thanks
> > Ed
> >
> > Edward Moss, CCNP, CCDP
> >
> >
> >
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
