Quoted form the Cisco IOS Software Command Summary ver 11.1 hard copy. [no] dce-terminal-timing enable When running the line at high speeds and long distances, use the "dce-terminal-timing enable" interface configuration command to prevent phase shifting of the data with respect to the clock. If SCTE is not available from the DTE, use "no" form of this command, which causes the DCE to use its own clock instead of SCTE from the DTE. Now, who wants to volunteer with an explanation of SCTE. > -----Original Message----- > From: Gareth Hinton [mailto:[EMAIL PROTECTED]] > Sent: Wednesday, March 07, 2001 5:58 PM > To: [EMAIL PROTECTED] > Subject: Re: Off Topic RE: strange question about dce setting? > > > From what I've seen of this command, it seems to allow a DCE > interface to > receive timing from a DTE. > Would like to see a decent explanation of its function. > Never seen it before. I'm not sure whether you're using it in > error when you > should be using a DCE cable and setting clockrate, or whether > you're ahead > of me and you know a neat trick. > > Cheers, > > Gareth > > ""Nigel Taylor"" <[EMAIL PROTECTED]> wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > Robert, > > Where have you been..? Haven't seen you in the > group for > > sometime. I was also wondering about Bob Envry of VA/DC/MD > CPAW fame > > haven't heard from him in a while as well. > > > > Anyway, good to see that you're still around..(our famous cable > guy)....:-) > > > > Nigel.. > > > > ----- Original Message ----- > > From: robert lowery <[EMAIL PROTECTED]> > > Newsgroups: groupstudy.cisco > > To: <[EMAIL PROTECTED]>; Eric ding <[EMAIL PROTECTED]> > > Sent: Wednesday, March 07, 2001 8:58 AM > > Subject: Re: strange question about dce setting? > > > > > > > Have you tried to use a special crossover cable... that > is db60 both > ends > > but wired with > > > one end dce and the other dte. To make it work you add > the command > > clockrate 64000 (for > > > example) on the interface that has the dce end. If you try to add > > clockrate on the dte > > > end ..it will not allow you to do so. If you do a show > controler serial > > (port no) it > > > will tell you what type of end is attached. > > > > > > ps I sell these specials cables on ebay and direct. > > > > > > bob...aka barronvonpuppy > > > > > > > > > Eric ding wrote: > > > > > > > two 2500 routers,routerA and routerB, back-to-back > connection .both > of > > > > them use serial 0,when i set routerA's serial for dce,i got the > output > > > > below: > > > > routerA(config-if)#dce-terminal-timing-enable > > > > %not allowed on dte interface > > > > but if i use the command below: > > > > routerA(config-if)#no dce-terminal-timing-enable > > > > routerA(config-if)#dce-terminal-timing-enable > > > > it does work. > > > > i was confused about it! > > > > any suggestion will be appreciated! > > > > > > > > _________________________________ > > > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > > > Report misconduct and Nondisclosure violations to > [EMAIL PROTECTED] > > > > > > _________________________________ > > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > > Report misconduct and Nondisclosure violations to > [EMAIL PROTECTED] > > > > > > > _________________________________ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to > [EMAIL PROTECTED] > > > > > _________________________________ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct > and Nondisclosure violations to [EMAIL PROTECTED] > _________________________________ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
