sounds like config register to me.
if you do a sh ver, and it's set to something other than 0x2102 would boot
config off a tftp server, then change it
config-reg 0x2102
write your (empty) configuration
and reload
(if you're working on your certification, you'd be wise to know where that
information is:
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/cis2500/2509/acsvrug/maint.htm#xtocid1285318
"Arthur Simplina" <[EMAIL PROTECTED]> wrote:
> This was discussed earlier regarding the error message for a tftp server.
> However, my question was still unanswered.
>
> As suggested, the way to correct this is as follows:
>
> Router(config)#no service config
> Router(config)#Ctrl-Z
>
> This eliminates the error message during the session. But after clearing up
> the config (for another lab set-up), the tftp error problem repeats.
>
> To clear the config I do:
> Router#erase nvram
> Router#reload
>
> After these commands and the router boots up, the tftp error problem
> reappears. I notice though that this problem occurs not with all the routers
> after the reload. Could this be a IOS version specific problem or this has
> something to do with the configuration register?
>
> Thanks for the help.
>
> Arthur
>
> -----------------------------------------------
>
>
> Cisco Internetwork Operating System Software
> IOS (tm) C2600 Software (C2600-DO3S-M), Version 12.0(5)T1, RELEASE SOFTWARE
> (fc
> 1)
> Copyright (c) 1986-1999 by cisco Systems, Inc.
> Compiled Tue 17-Aug-99 13:18 by cmong
> Image text-base: 0x80008088, data-base: 0x80CB67B0
>
> cisco 2621 (MPC860) processor (revision 0x102) with 26624K/6144K bytes of
> memory
> .
> Processor board ID JAD04410AGB (2818685363)
> M860 processor: part number 0, mask 49
> Bridging software.
> X.25 software, Version 3.0.0.
> Basic Rate ISDN software, Version 1.1.
> 2 FastEthernet/IEEE 802.3 interface(s)
> 2 Serial(sync/async) network interface(s)
> 1 ISDN Basic Rate interface(s)
> 32K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read/Write)
>
> %Error opening tftp://255.255.255.255/network-confg (Timed out)
> %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
> SETUP: new interface FastEthernet0/0 placed in "shutdown" state
> SETUP: new interface Serial0/0 placed in "shutdown" state
> SETUP: new interface BRI0/0 placed in "shutdown" state
> SETUP: new interface FastEthernet0/1 placed in "shutdown" state
> %Error opening tftp://255.255.255.255/network-confg (Timed out)
> %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
> %Error opening tftp://255.255.255.255/router-confg (Timed out)
> %Error opening tftp://255.255.255.255/ciscortr.cfg (Timed out)
>
>
> Press RETURN to get started!
> _________________________________________________________________
> Get your FREE download of MSN Explorer at http://explorer.msn.com
>
> _________________________________
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
____________________________________________________________________
Get free email and a permanent address at http://www.netaddress.com/?N=1
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
