Hi Chris,
What I am about to do is to add a T-1 wic to the 1600 and see if I can make
a frame switch and connect it to another 1602 and a 2610. The config that I
used if from the TAC website(- my own ip's) and it is only b/w the 2 1602
routers, which is different than configuring it on a 2501 switch which is
b/w 3 routers.
I'll let you know how that goes.
But here is the config for the 2 1602's:
Router 1:
#conf t
#int s0
#no ip address
#encap frame-relay
#clock rate 64000
#no keepalive
#exit
#int s0.1 point-to-point
#ip addr 1.1.1.1 255.255.255.0
#frame-relay interface-dlci 100 broadcast
*** I have the clock source internal configured on this guy ***
Router 2:
#conf t
#frame-relay switching
# int s0
#no ip address
#encap frame-relay
#no keepalive
#frame-relay intf-type dce
#exit
#int s0.1 point-to-point
#ip addr 1.1.1.2 255.255.255.0
#frame-relay interface-dlci 100 broadcast
*** I have the clock source line configured on this guy ***
Both routers have the 56kbps wic card connected via a console cable.
The only command that does not work is the sh frame lmi (obviously becoz' of
the no keep command)
All the other commands viz. sh frame pvc, sh frame map etc work.
Good luck.
Kind regards,
Niraj
>From: "Hayes, Christopher"
>To: 'Niraj Palikhey'
>Subject: RE: 1600's - Using to make a Frame Switch [7:4643]
>Date: Fri, 18 May 2001 07:44:25 -0400
>
>Niraj,
>
>Can you share a copy of the config?
>
>Chris
>
>-----Original Message-----
>From: Niraj Palikhey [mailto:[EMAIL PROTECTED]]
>Sent: Thursday, May 17, 2001 3:45 AM
>To: [EMAIL PROTECTED]
>Subject: Re: 1600's - Using to make a Frame Switch [7:4643]
>
>
>Well, after spending some time once again on CCO, this time using TAC's
>help, I finally figured out how to configure a 1602 router as a frame-relay
>switch and connect another router to it. It's actally very simple with one
>side R-1 providing the clock(56000) and the other side R-2 configured with
>the frame-relay switching command. Both routers are configured with s0.1
>point-to-point subif and an ip address, a common dlci specified for both
>and
>
>only on R-2 the frame-relay intf-type dce command configured. It works!!
>Now the next step is to install another 56kbps wic on one and configure it
>to route frame packets b/w 2 dlci's. It should be the same as for the 2501,
>I figure.
>Also figured out that the frame-relay intf-type and the frame-relay route
>commands can actually be configured on the routers.
>Thanks, Phil once again for your help.
>Kind regards,
>Niraj
>
>I guess this helps the other gentleman who needed to know this.
>
>
>
> >From: "Circusnuts"
> >Reply-To: "Circusnuts"
> >To: [EMAIL PROTECTED]
> >Subject: Re: 1600's - Using to make a Frame Switch [7:4643]
> >Date: Wed, 16 May 2001 19:38:44 -0400
> >
> >Might not be possible... I checked the CCO & I don't see an Enterprise
> >model IOS (but I did notice 12.2 is out :o) Do you have a CCO login ???
> >You could try Open Forum. I would guess not too many people have 1600
> >routers in their homelab.
> >
> >Sorry
> >Phil
> >
> >----- Original Message -----
> >From: Niraj Palikhey
> >To:
> >Sent: Wednesday, May 16, 2001 12:11 PM
> >Subject: Re: 1600's - Using to make a Frame Switch [7:4643]
> >
> >
> > > Hi Phil,
> > > It's you to the rescue again. :-)
> > > But unfortunately, it will not let me type the frame-relay intf-type
>dce
> >and
> > > the frame-relay route 100..... commands. Is there something that I
>have
> >to
> > > do on the 1602 for this?(Since it has a 56kbps wic with a built-in
> >csu/dsu).
> > > I scoured the CCO with no luck.
> > > I am wondering there should be a way because it DOES let me type the
> > > frame-relay switching global config command?
> > > Thanks,
> > > Niraj
> > > ** Anyone out there that can help :-( **
> > >
> > >
> > > >From: "Circusnuts"
> > > >Reply-To: "Circusnuts"
> > > >To: [EMAIL PROTECTED]
> > > >Subject: Re: 1600's - Using to make a Frame Switch [7:4643]
> > > >Date: Wed, 16 May 2001 00:21:52 -0400
> > > >
> > > >It shouldn't be any different than a 4 port router. I'm not sure
>what
> >is
> > > >supported in the 1600 IOS, but here is a basic template of the Telco
> >Cloud
> > > >config.
> > > >
> > > >interface Serial0
> > > > no ip address
> > > > encapsulation frame-relay
> > > > frame-relay lmi-type ansi
> > > > frame-relay intf-type dce
> > > > frame-relay route 102 interface Serial1 201
> > > > frame-relay route 103 interface Serial2 301
> > > > frame-relay route 105 interface Serial3 501
> > > >!
> > > >interface Serial1
> > > > no ip address
> > > > encapsulation frame-relay
> > > > frame-relay lmi-type ansi
> > > > frame-relay intf-type dce
> > > > frame-relay route 201 interface Serial0 102
> > > >
> > > >Phil
> > > >
> > > >----- Original Message -----
> > > >From: Gary Hughes
> > > >To:
> > > >Sent: Tuesday, May 15, 2001 11:52 PM
> > > >Subject: 1600's - Using to make a Frame Switch [7:4643]
> > > >
> > > >
> > > > > Anybody know the config's to make a 4 port Frame-Switch from 2
> >1600's
> > > >(both
> > > > > with 2 serial ports)
> > > > > FAQ, list archives, and subscription info:
> > > >http://www.groupstudy.com/list/cisco.html
> > > > > Report misconduct and Nondisclosure violations to
> >[EMAIL PROTECTED]
> > > >FAQ, list archives, and subscription info:
> > > >http://www.groupstudy.com/list/cisco.html
> > > >Report misconduct and Nondisclosure violations to
>[EMAIL PROTECTED]
> > >
> > > _________________________________________________________________
> > > Get your FREE download of MSN Explorer at http://explorer.msn.com
> > > FAQ, list archives, and subscription info:
> >http://www.groupstudy.com/list/cisco.html
> > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> >FAQ, list archives, and subscription info:
> >http://www.groupstudy.com/list/cisco.html
> >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
>_________________________________________________________________
>Get your FREE download of MSN Explorer at http://explorer.msn.com
>FAQ, list archives, and subscription info:
>http://www.groupstudy.com/list/cisco.html
>Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=5089&t=4643
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
