You need "transport output telnet"--this is the default, but you've
overrridden it with the "none" parameter.
Enjoy!
--
--------------------------------------------
Richard Deal
[EMAIL PROTECTED]
* Author of the following Coriolis books: CCNP Switching Exam Cram, CCNP
Remote Access Exam Prep, and CCNP Cisco Lan Switch Configuration; as well as
a CCNP test author for www.equizware.com
--------------------------------------------
""Jeongwoo Park"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi all
>
> I made some changes on config.
>
> Still didn't work.
>
> Here is new config:
>
>
>
> TermServer#sh run
>
> Building configuration...
>
> Current configuration:
>
> !
>
> version 12.0
>
> service timestamps debug uptime
>
> service timestamps log uptime
>
> no service password-encryption
>
> !
>
> hostname TermServer
>
> !
>
> enable password wams
>
> !
>
> ip subnet-zero
>
> no ip domain-lookup
>
> ip host r1 2001 1.1.1.1
>
> ip host r2 2002 1.1.1.1
>
> ip host r3 2003 1.1.1.1
>
> !
>
> !
>
> !
>
> interface Loopback0
>
> ip address 1.1.1.1 255.255.255.255
>
> no ip directed-broadcast
>
> !
>
> interface Ethernet0
>
> no ip address
>
> no ip directed-broadcast
>
> shutdown
>
> !
>
> interface Serial0
>
> ip address 5.5.5.5 255.255.255.0
>
> no ip directed-broadcast
>
> no ip mroute-cache
>
> no fair-queue
>
> clockrate 64000
>
> !
>
> interface Serial1
>
> ip address 5.5.6.5 255.255.255.0
>
> no ip directed-broadcast
>
> !
>
> ip classless
>
> !
>
> !
>
> line con 0
>
> no exec
>
> transport input none
>
> line 1 8
>
> transport input all
>
> transport output none
>
> stopbits 1
>
> line aux 0
>
> line vty 0 4
>
> login
>
> !
>
> end
>
> Now I did "sh line"
>
> TermServer#sh line
>
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
>
> * 0 CTY - - - - - 15 0 0/0 -
>
> * 1 TTY 9600/9600 - - - - - 7 20 4/17 -
>
> * 2 TTY 9600/9600 - - - - - 7 0 0/0 -
>
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
>
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
>
> 5 TTY 9600/9600 - - - - - 0 323 179/539 -
>
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
>
> 7 TTY 9600/9600 - - - - - 0 15 119/356 -
>
> * 8 TTY 9600/9600 - - - - - 0 22 21/63 -
>
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
>
> 10 VTY - - - - - 0 0 0/0 -
>
> 11 VTY - - - - - 0 0 0/0 -
>
> 12 VTY - - - - - 0 0 0/0 -
>
> 13 VTY - - - - - 0 0 0/0 -
>
> 14 VTY - - - - - 0 0 0/0 -
>
> Then I did this
>
> TermServer#clear line 1
>
> [confirm]
>
> [OK]
>
> TermServer#clear line 2
>
> [confirm]
>
> [OK]
>
> TermServer#clear line 8
>
> [confirm]
>
> [OK]
>
> TermServer#sh line
>
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
>
> * 0 CTY - - - - - 15 0 0/0 -
>
> 1 TTY 9600/9600 - - - - - 7 90 7/26 -
>
> 2 TTY 9600/9600 - - - - - 7 0 0/0 -
>
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
>
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
>
> 5 TTY 9600/9600 - - - - - 0 323 179/539 -
>
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
>
> 7 TTY 9600/9600 - - - - - 0 15 119/356 -
>
> * 8 TTY 9600/9600 - - - - - 0 22 21/63 -
>
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
>
> 10 VTY - - - - - 0 0 0/0 -
>
> 11 VTY - - - - - 0 0 0/0 -
>
> 12 VTY - - - - - 0 0 0/0 -
>
> 13 VTY - - - - - 0 0 0/0 -
>
> 14 VTY - - - - - 0 0 0/0 -
>
> Now it shows this:
>
> TermServer#sh line
>
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
>
> * 0 CTY - - - - - 15 0 0/0 -
>
> 1 TTY 9600/9600 - - - - - 7 90 7/26 -
>
> 2 TTY 9600/9600 - - - - - 7 0 0/0 -
>
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
>
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
>
> 5 TTY 9600/9600 - - - - - 0 323 179/539 -
>
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
>
> 7 TTY 9600/9600 - - - - - 0 15 119/356 -
>
> * 8 TTY 9600/9600 - - - - - 0 22 21/63 -
>
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
>
> 10 VTY - - - - - 0 0 0/0 -
>
> 11 VTY - - - - - 0 0 0/0 -
>
> 12 VTY - - - - - 0 0 0/0 -
>
> 13 VTY - - - - - 0 0 0/0 -
>
> 14 VTY - - - - - 0 0 0/0 -
>
> At this point, I am confused because line 8 was not cleared.
>
> Now I typed "r1" This is what it looks like:
>
> TermServer#r1
>
> Trying r1 (1.1.1.1, 2001)... Open
>
> And I get stuck forever.
>
> I had to go (ctrl+shift+6)+X to go back to TermServer prompt.
>
> At TermServer prompt, I did "sh line" again.
>
> TermServer#sh line
>
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
>
> * 0 CTY - - - - - 16 0 0/0 -
>
> * 1 TTY 9600/9600 - - - - - 8 90 7/26 -
>
> 2 TTY 9600/9600 - - - - - 7 0 0/0 -
>
> 3 TTY 9600/9600 - - - - - 1 0 0/0 -
>
> 4 TTY 9600/9600 - - - - - 0 0 0/0 -
>
> 5 TTY 9600/9600 - - - - - 0 323 179/539 -
>
> 6 TTY 9600/9600 - - - - - 0 0 0/0 -
>
> 7 TTY 9600/9600 - - - - - 0 15 119/356 -
>
> * 8 TTY 9600/9600 - - - - - 0 22 21/63 -
>
> 9 AUX 9600/9600 - - - - - 0 0 0/0 -
>
> 10 VTY - - - - - 0 0 0/0 -
>
> 11 VTY - - - - - 0 0 0/0 -
>
> 12 VTY - - - - - 0 0 0/0 -
>
> 13 VTY - - - - - 0 0 0/0 -
>
> 14 VTY - - - - - 0 0 0/0 -
>
> So I cleared line 1 by doing this "clear line 1"
>
> And typed r1. It still showed this @!#$.
>
> TermServer#r1
>
> Trying r1 (1.1.1.1, 2001)... Open
>
> I just made longer message than I intended to. But since I am struggling
to
> get this to work, I want to try every possible way.
>
> I hope I showed you better.
>
> Any input would be appreciated
>
> Thanks.
>
> Jeongwoo
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=5181&t=5177
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
