Yeah, I started thinking the same thing after my post. Since the telnet
session is really just setting you up to do a console connection the
connected
router, typing 'exit' would only drop you back to the "Press enter to
continue"
blah message...
The telnet session is really established to the 2511, and since your
keystrokes
are redirected to the serial line, the 'exit' is never seen by the term
server.
So what's the best way to do this? Would it be typing 'exit,' and then
issuing
a Ctl-Shift-6 - x, followed by another 'exit?'
----- Original Message -----
From: "Circusnuts"
To: "W. Alan Robertson" ;
Sent: Thursday, May 24, 2001 12:05 AM
Subject: Re: CORRECTION: Re: reverse telnet [7:5655]
> I was thinking the same, but this would clear all lines. The next telnet
> session onto the 2511 would require re-establishing the session & clearing
> the line to pass onto the UNIX box (if I am understanding the setup
> correctly).
>
> I'm thinking the user needs to turn their underwear back around to the
> correct direction or use an Alias :o)
>
> Phil
>
> ----- Original Message -----
> From: W. Alan Robertson
> To:
> Sent: Wednesday, May 23, 2001 11:30 PM
> Subject: Re: CORRECTION: Re: reverse telnet [7:5655]
>
>
> > When I first read the original message, my response seemed too simple, so
> I
> > didn't reply...
> >
> > Here it is: Type 'exit', and hit enter.
> >
> > Does this not meet the requirements? Does the line get hung up or
> something?
> > Is there more to this question than meets the eye?
> >
> > ----- Original Message -----
> > From: "Frank Kim"
> > To:
> > Sent: Wednesday, May 23, 2001 10:55 PM
> > Subject: CORRECTION: Re: reverse telnet [7:5655]
> >
> >
> > > Hi folks,
> > > I know about the ctrl-shift-6 x. Please read my message again. I am
> not
> > > telnet'ing from the 2511. I sit on another workstation which is on the
> > > same network as the ethernet segment of the 2511 and I telnet from
> there.
> > > Please re-read my question. Sorry for the confusion.
> > >
> > >
> > > -Frank
> > >
> > >
> > > On Wed, 23 May 2001, Kevin Wigle wrote:
> > >
> > > > with this simple scenario all you need do is:
> > > >
> > > > control-shift-6 (all at one time)
> > > >
> > > > release
> > > >
> > > > and then type x
> > > >
> > > > this should bring you back to the terminal server
> > > >
> > > > then type the command: disconnect 1
> > > >
> > > > r1 is gone and you're left with the terminal server connection
> > > >
> > > > Kevin Wigle
> > > >
> > > > ----- Original Message -----
> > > > From: "Frank Kim"
> > > > To:
> > > > Sent: Wednesday, 23 May, 2001 20:38
> > > > Subject: reverse telnet [7:5655]
> > > >
> > > >
> > > > > Below is my config of a 2511. My question is if I sit on another
> > > > > workstation and telnet to 192.168.1.1 2001 which brings me to R1.
> Once
> > > > > I am in, is there a 'key-stroke' I can enter in to have the 2511
> > > terminate
> > > > > my session? I'm currently closing out my telnet application to
have
> > the
> > > > > session terminated. Thanks for any help.
> > > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=5681&t=5655
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
