PLEASE GUYS, when you reply to my post, unless i ask you to reply to me,
reply on the list, so that everyone else can learn from the thread!
Now, on to the goodies.
Ok. now.first off, those 32 ethernet interfaces are switched ports. you
configure them on the switch, and trunk the vlans over the two
gigabit-ethernet interfaces that the 4232 connects to the backplane with.
OK. Now, g 3 and 4 interface DIRECTLY TO THE BACKPLANE. on the router, and
on the switch, those interfaces are numbered 1 and 2.
youll notice on the switched interfaces of the blade, the last one is
numbered 34....
Now, what i did in my favorite installation of this was put those two gig
ints into a channel group.
on the router, the commands will look lik the following,
int gig 3
channel 1
no shut
int gig 4
channel 1
no shut
int port-cha 1
...make sure it exists.
int port-c 1.1
encap dot1q 1
...keep in mind im pulling these commands outta my Arse and they could be
wrong, i do that sometimes...
on the switch, do a
set port chan
command.
Im going to get you a config for one of these things and post it, but i dont
remeber the ip address.
ill get it tomorrow at work...
----- Original Message -----
From: "LaVillie Tate"
To: "Peter Slow"
Sent: Wednesday, June 20, 2001 4:46 PM
Subject: RE: Layer 3 Module on 4006 [7:9229]
> Trying to remove port-channels and receiving the
> following error message % Removal of physical
> interfaces is not permitted. Also trying to assign ip
> addresses to 32 fe ports. Last, do ge3 and ge4 receive
> there internet ip addresses once ge1 and ge2 are up or
> do I have to assign them? This is my first time
> working with a catalyst 4000 switch, thank so much for
> your help.
> --- Peter Slow wrote:
> > What are you having trouble with, i know the stupid
> > little ws-x4232-L3
> > module quite well....
> > (I don't like it tho)
> >
> > Peter Slow, CCNP Voice Specialist
> > Network Engineer
> > Planetary Networks
> > 535 West 34th. Street
> > New York, New York
> > 10001
> >
> > Cell: +1(516) 782.1535
> > Desk: +1(646) 792.2395
> > Mail: [EMAIL PROTECTED]
> >
> >
> >
> > -----Original Message-----
> > From: LaVillie Tate [mailto:[EMAIL PROTECTED]]
> > Sent: Wednesday, June 20, 2001 2:29 PM
> > To: [EMAIL PROTECTED]
> > Subject: Layer 3 Module on 4006 [7:9229]
> >
> >
> > Does anyone have any sample configurations I can
> > look
> > at for the layer 3 module on a catalyst 4000. I
> > have
> > a 4006 and I'm having a little trouble configing the
> > layer 3 services. I've already searched the cisco
> > site. Any help would be gladly accepted.
> >
> > Thanks in advance
> >
> > LaVillie Tate
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Get personalized email addresses from Yahoo! Mail
> > http://personal.mail.yahoo.com/
> [EMAIL PROTECTED]
>
>
> __________________________________________________
> Do You Yahoo!?
> Get personalized email addresses from Yahoo! Mail
> http://personal.mail.yahoo.com/
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=9448&t=9229
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
