Why pull it out of your arse when you can look at this:
http://www.cisco.com/warp/public/473/28.html
If you haven't read this doc, read it and you'll learn a lot.
by the way, the group is cc: on this message.
>From: "Peter I. Slow"
>Reply-To: "Peter I. Slow"
>To: [EMAIL PROTECTED]
>Subject: Re: Layer 3 Module on 4006 [7:9229]
>Date: Thu, 21 Jun 2001 19:54:48 -0400
>
>PLEASE GUYS, when you reply to my post, unless i ask you to reply to me,
>reply on the list, so that everyone else can learn from the thread!
>
>Now, on to the goodies.
>
>Ok. now.first off, those 32 ethernet interfaces are switched ports. you
>configure them on the switch, and trunk the vlans over the two
>gigabit-ethernet interfaces that the 4232 connects to the backplane with.
>
>OK. Now, g 3 and 4 interface DIRECTLY TO THE BACKPLANE. on the router, and
>on the switch, those interfaces are numbered 1 and 2.
>youll notice on the switched interfaces of the blade, the last one is
>numbered 34....
>
>Now, what i did in my favorite installation of this was put those two gig
>ints into a channel group.
>on the router, the commands will look lik the following,
>int gig 3
>channel 1
>no shut
>int gig 4
>channel 1
>no shut
>int port-cha 1
>...make sure it exists.
>int port-c 1.1
>encap dot1q 1
>
>...keep in mind im pulling these commands outta my Arse and they could be
>wrong, i do that sometimes...
>
>on the switch, do a
>set port chan
>command.
>Im going to get you a config for one of these things and post it, but i
>dont
>remeber the ip address.
>ill get it tomorrow at work...
>
>
>
>
>
>
>----- Original Message -----
>From: "LaVillie Tate"
>To: "Peter Slow"
>Sent: Wednesday, June 20, 2001 4:46 PM
>Subject: RE: Layer 3 Module on 4006 [7:9229]
>
>
> > Trying to remove port-channels and receiving the
> > following error message % Removal of physical
> > interfaces is not permitted. Also trying to assign ip
> > addresses to 32 fe ports. Last, do ge3 and ge4 receive
> > there internet ip addresses once ge1 and ge2 are up or
> > do I have to assign them? This is my first time
> > working with a catalyst 4000 switch, thank so much for
> > your help.
> > --- Peter Slow wrote:
> > > What are you having trouble with, i know the stupid
> > > little ws-x4232-L3
> > > module quite well....
> > > (I don't like it tho)
> > >
> > > Peter Slow, CCNP Voice Specialist
> > > Network Engineer
> > > Planetary Networks
> > > 535 West 34th. Street
> > > New York, New York
> > > 10001
> > >
> > > Cell: +1(516) 782.1535
> > > Desk: +1(646) 792.2395
> > > Mail: [EMAIL PROTECTED]
> > >
> > >
> > >
> > > -----Original Message-----
> > > From: LaVillie Tate [mailto:[EMAIL PROTECTED]]
> > > Sent: Wednesday, June 20, 2001 2:29 PM
> > > To: [EMAIL PROTECTED]
> > > Subject: Layer 3 Module on 4006 [7:9229]
> > >
> > >
> > > Does anyone have any sample configurations I can
> > > look
> > > at for the layer 3 module on a catalyst 4000. I
> > > have
> > > a 4006 and I'm having a little trouble configing the
> > > layer 3 services. I've already searched the cisco
> > > site. Any help would be gladly accepted.
> > >
> > > Thanks in advance
> > >
> > > LaVillie Tate
> > >
> > > __________________________________________________
> > > Do You Yahoo!?
> > > Get personalized email addresses from Yahoo! Mail
> > > http://personal.mail.yahoo.com/
> > [EMAIL PROTECTED]
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Get personalized email addresses from Yahoo! Mail
> > http://personal.mail.yahoo.com/
_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=9456&t=9229
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
