Did you check the jumper the applique on the AGS+ serial interface to make
it DCE?  It was on the webpage that was presented in a previous email.

-e-

----- Original Message -----
From: Charles Ryan 
To: 
Sent: Friday, July 20, 2001 2:44 PM
Subject: Re: AGS+ as a frame-relay switch [7:13133]


> I'm getting this from "debug frame-relay lmi":
>
>
> Serial0(in): Unexpected StEnq, clock 1535608
> Serial0(out): StEnq, clock 1542300, myseq 13, yourseen 0, DTE down
>  datagramstart = 0x558B18, datagramsize = 14
>
>  FR encap = 0x00010308
> 00 75 95 01 01 00 03 02 0D 00
>
> Serial0(in): Unexpected StEnq, clock 1545608
> Serial0(out): StEnq, clock 1552300, myseq 14, yourseen 0, DTE down
>  datagramstart = 0x558B18, datagramsize = 14
>
>  FR encap = 0x00010308
> 00 75 95 01 01 00 03 02 0E 00
>
> Serial0(in): Unexpected StEnq, clock 1555608
> Serial0(out): StEnq, clock 1562300, myseq 15, yourseen 0, DTE down
>  datagramstart = 0x558B18, datagramsize = 14
>
>  FR encap = 0x00010308
> 00 75 95 01 01 00 03 02 0F 00
>
> Serial0(in): Unexpected StEnq, clock 1565608
> Serial0(out): StEnq, clock 1572300, myseq 16, yourseen 0, DTE down
>  datagramstart = 0x558B18, datagramsize = 14
>
>  FR encap = 0x00010308
> 00 75 95 01 01 00 03 02 10 00
>
> Serial0(in): Unexpected StEnq, clock 1575608
> Serial0(out): StEnq, clock 1582300, myseq 17, yourseen 0, DTE down
>  datagramstart = 0x558B18, datagramsize = 14
>
> It's almost like it's confused that it's receiving clock source from the
> other end of the connection, and is trying to provide clocking on it's
own.
>
> In looking at the "show controllers mci" command, it shows that the ports
> are setup for DTE, so now I'm really confused. Swapping cables didn't
work,
> line protocol comes up, then goes down.
>
> I'll keep digging......
>
> ----- Original Message -----
> From: "Hire, Ejay"
> To:
> Sent: Friday, July 20, 2001 5:22 PM
> Subject: RE: AGS+ as a frame-relay switch [7:13133]
>
>
> > It doesn't matter which end of the cable is dce, as long as you are
using
> a
> > dte-dce cable and the dce end is configured with a clock rate.
> >
> > I have an AGS configured as a frame-relay switch with a csc/4t serial
card
> > and HDv.35 dce to Cisco HD60 Dte cables.  I also had difficulty getting
> the
> > confuration to work until I RTFM and discovered that I had to change a
> > jumper on the CSC/4t serial card to place the ags ports in DCE mode.
> >
> > Here is a my config
> > version 10.2
> >
> > service config
> >
> > !
> >
> > enable secret 5 $1$1uBB$Tg1x6HtEuWjLJCsVgGEp11
> >
> > enable password passwor
> >
> > !
> >
> > frame-relay switching
> >
> > !
> >
> > interface Ethernet0
> >
> > no ip address
> >
> > shutdown
> >
> >
> > ...
> >
> >
> > interface Ethernet11
> >
> > no ip address
> >
> > shutdown
> >
> > !
> >
> > interface Serial0
> >
> > ip address 10.1.0.2 255.255.255.0
> >
> > encapsulation frame-relay
> >
> > clockrate 64000
> >
> > frame-relay intf-type dce
> >
> > frame-relay route 16 interface Serial1 17
> >
> > !
> >
> > interface Serial1
> >
> > ip address 10.2.0.1 255.255.255.0
> >
> > encapsulation frame-relay
> >
> > clockrate 64000
> >
> > frame-relay intf-type dce
> >
> > frame-relay route 17 interface Serial0 16
> >
> > !
> >
> >
> > ...
> > !
> >
> > line con 0
> >
> > exec-timeout 0 0
> >
> > line aux 0
> >
> > line vty 0 4
> >
> > password password
> >
> > login
> >
> > !
> >
> > end
> >
> >
> >
> > -----Original Message-----
> > From: Charles Ryan [mailto:[EMAIL PROTECTED]]
> > Sent: Friday, July 20, 2001 4:04 PM
> > To: [EMAIL PROTECTED]
> > Subject: AGS+ as a frame-relay switch [7:13133]
> >
> >
> > Apologies if this has already been covered once before.....
> >
> > Quick question regarding setting up an AGS+ as a frame switch.
> >
> > Do the cables connecting to the AGS+ have to be DCE in order to get the
> > frame-relay switching to work, or can it still work if the cables are
DTE?
> I
> > currently have DTE cables into the AGS+ and am not getting line protocol
> to
> > come up, even though the other ends are DCE and I have "clock rate
64000"
> > configured on the other ends.
> >
> > I also have encap frame-realy ietf on both sides, frame-relay lmi-type
> ansi
> > as well.
> >
> > I'll search the archives while I await an answer.
> >
> > Thanks!
> >
> > -Chuck
> >
> >
> >
> > _________________________________________________________
> > Do You Yahoo!?
> > Get your free @yahoo.com address at http://mail.yahoo.com
> _________________________________________________________
> Do You Yahoo!?
> Get your free @yahoo.com address at http://mail.yahoo.com
_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address at http://mail.yahoo.com




Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=13145&t=13133
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]

Reply via email to