Bob,
You really have to watch those configs :P
The IP for Interface Eth 0/1 is 192.168.0.6 (a conflict with your laptop). I
assume that you want it to be 192.168.0.1 (or whatever you want the gateway
to be, make sure that you also set this gateway on your laptop_
""Bob Lepine"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Thanks for your help. You're right. I didn't watch that access list. I
have
> a new configuration. I seem to be able to get out my router and ping the
> dhcp server as well as the name servers. But I have a connection to my
e0/1
> from my laptop which is 192.168.0.6. I can ping from my laptop to e0/1,
but
> I can't ping from my laptop to e0/0. I'm not getting through the router.
Any
> more suggestions?
>
> Here's my updated config
> 03:05:07: %SYS-5-CONFIG_I: Configured from console by consolen
> Building configuration...
>
> Current configuration : 810 bytes
> !
> version 12.1
> no service single-slot-reload-enable
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname BobRouter
> !
> logging rate-limit console 10 except errors
> !
> ip subnet-zero
> !
> !
> no ip finger
> !
> !
> !
> !
> interface Ethernet0/0
> ip address dhcp
> ip nat outside
> half-duplex
> !
> interface Serial0/0
> no ip address
> shutdown
> !
> interface BRI0/0
> no ip address
> shutdown
> !
> interface Ethernet0/1
> ip address 192.168.0.6 255.255.255.0
> ip nat inside
> half-duplex
> !
> router rip
> network 24.0.0.0
> network 192.168.0.0
> !
> ip nat inside source list 100 interface Ethernet0/0 overload
> ip classless
> ip route 0.0.0.0 0.0.0.0 Ethernet0/0
> no ip http server
> !
> access-list 100 permit ip any any
> !
> line con 0
> transport input none
> line aux 0
> line vty 0 4
> !
> no scheduler allocate
> end
>
> BobRouter#
>
> ------------------------------------------------------------------
> ""Wojtek Zlobicki"" wrote in message
> [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > You may want to take a look at your access list
> >
> > access-list 100 permit ip 192.0.0.0 0.0.0.255 any
> >
> > change to
> >
> > access-list 100 permit ip 192.168.0.0 0.0.0.255 any
> >
> > ""Bob Lepine"" wrote in message
> > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > > Hi, I've just been informed that easyip should work on my 2600 to get
me
> > to
> > > resolve the inside to outside network with a dhcp number.(I'm using a
> > cable
> > > modem and am assigned a dynamic number) I'm trying to go from my
inside
> > > network to the outside. The following is my configuration. I'm still
new
> > at
> > > this so something is obviously wrong.
> > > Building configuration...
> > >
> > > Current configuration : 784 bytes
> > > !
> > > version 12.1
> > > no service single-slot-reload-enable
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname BobRouter
> > > !
> > > logging rate-limit console 10 except errors
> > > !
> > > ip subnet-zero
> > > !
> > > !
> > > no ip finger
> > > !
> > > !
> > > !
> > > !
> > > interface Ethernet0/0
> > > ip address dhcp
> > > ip nat outside
> > > half-duplex
> > > !
> > > interface Serial0/0
> > > no ip address
> > > shutdown
> > > !
> > > interface BRI0/0
> > > no ip address
> > > shutdown
> > > !
> > > interface Ethernet0/1
> > > ip address 192.168.0.6 255.255.255.0
> > > ip nat inside
> > > half-duplex
> > > !
> > > ip nat inside source list 100 interface Ethernet0/0 overload
> > > ip classless
> > > ip route 0.0.0.0 0.0.0.0 Ethernet0/0 permanent
> > > no ip http server
> > > !
> > > access-list 100 permit ip 192.0.0.0 0.0.0.255 any
> > > !
> > > line con 0
> > > transport input none
> > > line aux 0
> > > line vty 0 4
> > > !
> > > no scheduler allocate
> > > end
> > > -----------------------------------------
> > > Any help would be appreciated
> > >
> > > --
> > > Bob Lepine
> > > MCSE,MCDBA,CNA,CCNA,MCT
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=19142&t=19127
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
