Ha! Ha! >From: "MADMAN" >Reply-To: "MADMAN" >To: [EMAIL PROTECTED] >Subject: Re: HSRP error with a BGP config!! [7:22179] >Date: Fri, 5 Oct 2001 21:40:59 -0400 > >BUG?!?!?!? > >Cisco Nuts wrote: > > > > > > > Oh! Yeah! > > > > The parameters do show up! No doubt about that. But the router does > > not take the command!! Any ideas?? > > >From: "MADMAN" > > >Reply-To: "MADMAN" > > >To: [EMAIL PROTECTED] > > >Subject: Re: HSRP error with a BGP config!! [7:22179] > > >Date: Fri, 5 Oct 2001 16:02:23 -0400 > > > > > >Here is the output of a 2500 running 11.2.17: > > > > > >c2522a#conf t > > >Enter configuration commands, one per line. End with CNTL/Z. > > >c2522a(config)#int e0 > > >c2522a(config-if)#standby ? > > > group number > > > authentication Authentication string > > > ip Enable hot standby protocol for IP > > > mac-refresh Refresh MAC cache on switch by periodically > > >sendingpacket > > > from virtual mac address > > > preempt Overthrow lower priority designated routers > > > priority Priority level > > > timers Hot standby timers > > > track Priority tracks this interface state > > > use-bia Hot standby uses interface's burned in address > > > > > > Dave > > > > > >Cisco Nuts wrote: > > > > > > > > Hi, > > > > It does take the command: > > > > #standby ip 192.168.21.10 > > > > but not the preempt and priority commands. > > > > I am using a 2511 router for this. Here is the #sh ver output: > > > > RTF#sh ver > > > > Cisco Internetwork Operating System Software > > > > IOS (tm) 2500 Software (C2500-D-L), Version 12.0(9), RELEASE > > SOFTWARE (fc1) > > > > Copyright (c) 1986-2000 by cisco Systems, Inc. > > > > Compiled Mon 24-Jan-00 22:06 by bettyl > > > > Image text-base: 0x030387D0, data-base: 0x00001000 > > > > > > > > ROM: System Bootstrap, Version 11.0(10c), SOFTWARE > > > > BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version > > 11.0(10c), RELEASE > > > > SOFTWARE (fc1) > > > > > > > > RTF uptime is 1 day, 14 hours, 1 minute > > > > System restarted by reload > > > > System image file is "flash:c2500-d-l.120-9.bin" > > > > > > > > cisco 2511 (68030) processor (revision M) with 2048K/2048K bytes > > of memory. > > > > Processor board ID 07144242, with hardware revision 00000000 > > > > Bridging software. > > > > X.25 software, Version 3.0.0. > > > > 1 Ethernet/IEEE 802.3 interface(s) > > > > 2 Serial network interface(s) > > > > 16 terminal line(s) > > > > 32K bytes of non-volatile configuration memory. > > > > 8192K bytes of processor board System flash (Read ONLY) > > > > > > > > Please advise. > > > > Thank you. > > > > Kind regards. > > > > > > > > >From: "Richard Botham" > > > > >Reply-To: "Richard Botham" > > > > >To: [EMAIL PROTECTED] > > > > >Subject: RE: HSRP error with a BGP config!! [7:22179] > > > > >Date: Fri, 5 Oct 2001 05:48:41 -0400 > > > > > > > > > >What type of router are you using. > > > > >It looks like you may be using MHSRP fom the show standby > > > > > > > > > >CCO states that some older lower end routers using Lance /Quicc > > ethernet > > > > >hardware will only support a single hsrp group and therefore only > > a single > > > > >unicast mac address. > > > > >Hope this helps. > > > > >Richard > > > > _________________________________________________________________ > > > > Get your FREE download of MSN Explorer at > > http://explorer.msn.com/intl.asp > > >-- > > >David Madland > > >Sr. Network Engineer > > >CCIE# 2016 > > >Qwest Communications Int. Inc. > > >[EMAIL PROTECTED] > > >612-664-3367 > > > > > >"Emotion should reflect reason not guide it" > > [EMAIL PROTECTED] > > > > > > ----------------------------------------------------------------------- > > Get your FREE download of MSN Explorer at http://explorer.msn.com > >-- >David Madland >CCIE# 2016 >Senior Network Engineer >Qwest Communications misconduct and Nondisclosure violations to [EMAIL PROTECTED]
------------------------------------------------------------------------ Get your FREE download of MSN Explorer at http://explorer.msn.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=22309&t=22179 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]