My bad... Theres the msfcautostate disble command which should eliminate the need to have an active port in a given VLAN before the interface comes up...
----- Original Message ----- From: "MADMAN" To: "Brant Stevens" Cc: Sent: Monday, October 22, 2001 12:55 PM Subject: Re: Intervlan Connectivity is not working? [7:23744] > > He doesn't need to trunk between switches, this is a single switch > with two MSFC's. Your HSRP looks fine but are the interfaces up?? If > you have no switch ports active in the designated VLANs the MSFC VLAN > will not come active. > > The management VLAN stuff is VTP, nothing to do with your problem. > > Do a sh stand vlan x, see what state they ae in. > > Dave > > Brant Stevens wrote: > > > > Are you trunking on any other ports? You need to trunk between switches if > > you want routing amongst multiple VLANs to become redundant via the MSFCs... > > > > ----- Original Message ----- > > From: "Washington Rico" > > To: > > Sent: Monday, October 22, 2001 12:10 AM > > Subject: Intervlan Connectivity is not working? [7:23744] > > > > > Cisco People I need you help... > > > > > > I would appreciate any help. I have a 6500Cat running Redundant > > Supervisor > > > engines and two MSFC installed one on each supervisor engine. > > > ***** > > > Mod Slot Ports Module-Type Model Sub Status > > > --- ---- ----- ------------------------- ------------------- --- -------- > > > 1 1 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes ok > > > 15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok > > > 2 2 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes standby > > > 16 2 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok > > > 3 3 8 1000BaseX Ethernet WS-X6408A-GBIC no ok > > > 4 4 8 1000BaseX Ethernet WS-X6408A-GBIC no ok > > > 6 6 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok > > > 7 7 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok > > > 8 8 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok > > > 9 9 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok > > > ***** > > > > > > I created one vlan (Vlan 20) and I want to use HSRP across the MSFC so the > > > clients can have a steady Gateway. > > > > > > Default vlan 1 works fine, I can ping accross to the other MSFC. But > > > Vlan20 the one I created on the switch does give me connectivity accoss > > > MFSC. > > > MSFC#1 > > > interface Vlan20 > > > ip address 10.224.173.3 255.255.255.0 > > > no ip redirects > > > ip route-cache flow > > > standby priority 80 preempt > > > standby authentication XXXX > > > standby ip 10.224.173.1 > > > MSFC#2 > > > interface Vlan20 > > > mac-address 0012.3456.7891 > > > ip address 10.224.173.2 255.255.255.0 > > > no ip redirects > > > ip route-cache flow > > > standby priority 90 preempt > > > standby authentication XXXX > > > standby ip 10.224.173.1 > > > ******** > > > Test-6500-MSFC2#ping 10.224.173.1 > > > > > > Type escape sequence to abort. > > > Sending 5, 100-byte ICMP Echos to 10.224.173.1, timeout is 2 seconds: > > > ..... > > > Success rate is 0 percent (0/5) > > > Test-6500-MSFC2# > > > ------ > > > ****** > > > On the switch trunks shows this... > > > > > > Test-6500> (enable) show trunk > > > * - indicates vtp domain mismatch > > > Port Mode Encapsulation Status Native vlan > > > -------- ----------- ------------- ------------ ----------- > > > 15/1 nonegotiate isl trunking 1 > > > 16/1 nonegotiate isl trunking 1 > > > > > > Port Vlans allowed on trunk > > > -------- > > > --------------------------------------------------------------------- > > > 15/1 1-1005,1025-4094 > > > 16/1 1-1005,1025-4094 > > > > > > Port Vlans allowed and active in management domain > > > -------- > > > --------------------------------------------------------------------- > > > 15/1 1 (enable) > > > > > > ********** > > > Show Vlan > > > VLAN Name Status IfIndex Mod/Ports, Vlans > > > ---- -------------------------------- --------- ------- > > > ------------------------ > > > 1 default active 199 1/1-2 > > > 2/1-2 > > > 20 TEST-VLAN active 208 > > > 30 VLAN30 active 207 > > > 999 Dead-Vlan active 225 3/1-8 > > > 4/1-8 > > > 6/1-48 > > > 7/1-48 > > > 8/1-48 > > > 9/1-48 > > > 1002 fddi-default active 200 > > > 1003 token-ring-default active 203 > > > 1004 fddinet-default active 201 > > > 1005 trnet-default active 202 > > > *********************************************************************** > > > > > > Question 1.----- > > > Why isn't vlan 20 and 30 and 999 in the Management domain? (Above Show > > > trunk command) > > > Question 2.----- > > > Becuase Vlan 20 and 30 aren't in the Management domain, Is this the reason > > > why I am getting no Msfc connectivity for those Vlans.. > > > > > > > > > Sorry for the long letter, appreciate any info you have.. > > > > > > Regards, > > > Eric > > > > > > > > > > > > _________________________________________________________________ > > > $B$+$o$$$$(B & > > $B;H$($k%V%i%&%6$G!"%$%s%?! http://explorer.msn.co.jp/ > -- > David Madland > Sr. Network Engineer > CCIE# 2016 > Qwest Communications Int. Inc. > [EMAIL PROTECTED] > 612-664-3367 > > "Emotion should reflect reason not guide it" Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=23796&t=23744 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]