Thanks Galo! I will try that. -h ----- Original Message ----- From: "Galo Villacis" To: Sent: Thursday, May 09, 2002 7:17 PM Subject: Re: dual-homed hosts problems [7:43677]
> I believe your issue may relate to the single IP stack on 2000. Try > defaulting traffic to the internet and adding a static route to the internal > network opposed to specifying the gateway on the internal IP interface. > Also I would go as far as disabling any NETBIOS on the external interface > for security. > > cmd would be: > > route add -p Network Mask Gateway > > ----- Original Message ----- > From: "Henrique Duarte" > To: > Sent: Thursday, May 09, 2002 5:48 PM > Subject: Re: dual-homed hosts problems [7:43677] > > > > Bulent, > > > > Thank you for the reply. I am afraid you may have misunderstood this > > problem. Allow me to be more clear: > > > > > > 192.168.0.1 --------------------- 192.168.0.150 - Host A - 128.59.39.3 > > | (dual > homed > > server) > > | > > | > > | > > | > > | > > 128.59.39.2 > > router A router > > C ---------------------------- Internet > > | > > 192.168.1.1 > > | > > | > > T1 > > | > > | > > 192.168.1.2 > > | > > router B > > | > > 192.168.2.1 > > > > > > The problem happens on Host A. Host A is a WebServer with 2 interfaces: > a > > public (which goes out to the internet) and a private (which talks to the > > database). The private interface has IP 192.168.0.150 and default GW > > 192.168.0.1. The public has ip 128.59.39.3 and default GW 128.59.39.2. > > Everything works fine if I leave the private interface's default GW blank. > > If I put Router C's address as the private interface's default gateway, > > after some time I cannot ping anywhere from Host A, even though I can ping > > it from the outside world. I need to have the private interface > configured > > with 192.168.0.1 as the default GW because remote users need to be able to > > connect to that server via the back-end T1. Any light would be greatly > > appreciated. > > > > Thanks, > > > > -H > > > > > > ----- Original Message ----- > > From: "B|lent ^ahin" > > To: > > Sent: Thursday, May 09, 2002 3:17 AM > > Subject: RE: dual-homed hosts problems [7:43677] > > > > > > > When configuring ethernet interfaces on MS environment, you have three > > blank > > > spaces to fill: IP_address, Subnet_mask and Default_gateway. So the > people > > > start to think every ethernet interface as a router: "This interface > will > > > route IP packets to the other interface, so the default gateway of the > > first > > > interface should be same as the IP address of the second interface.", > but > > > there is one router on the PC: CPU. Try to configure only one default > > > gateway. You can use the command "route print" to see what happens when > > you > > > configure two or more default gateways. > > > > > > Bulent > > > > > > > > > -----Original Message----- > > > From: Henrique Duarte [mailto:[EMAIL PROTECTED]] > > > Sent: Thursday, May 09, 2002 12:39 AM > > > To: [EMAIL PROTECTED] > > > Subject: dual-homed hosts problems [7:43677] > > > > > > > > > Hello All, > > > > > > I am working on some dual homed servers at a co-location where there is > a > > > public and private interface on each. The public interfaces attach to > the > > > internet via a router while the private ones are on its own separate > > private > > > subnet. The private subnet is attached to another router, which provides > > > remote users access to the private network via a T1 line. I am > > encountering > > > the following issue. When I set the private interfaces' default gateway > to > > > the private interface's router address, it works fine for about 10 > minutes > > > or so, but after that the server cannot ping and/or access the internet, > > > even though it is set with the public NIC to be the primary one. > However, > > as > > > soon as I take the default gateway out of the private interface NIC it > > works > > > fine and is able to ping the outside world. Does anyone have any ideas > why > > > this is happening and/or how to fix it? The servers are running Windows > > 2000 > > > Server and the T1 router is a Cisco 1601. > > > > > > Thanks, > > > > > > -Henrique Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=43800&t=43677 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
