Hi.. I had installed a gigabit switch (Cisco 3550). But I feel the speed
of slow. I connected my two PC in GigabitEthernet0/1 and 0/2. I transfer a
huge file between the two PCs ( the transfer last for 4 mins). But the
maximum speed is only 10Mbit ? Why?? What is wrong?? I thought it should
be go up to 1000M or 1Gbits???
!
interface GigabitEthernet0/1
no ip address
snmp trap link-status
!
interface GigabitEthernet0/2
no ip address
snmp trap link-status
!
interface GigabitEthernet0/3
no ip address
snmp trap link-status
!
interface GigabitEthernet0/4
no ip address
snmp trap link-status
!
interface GigabitEthernet0/5
no ip address
snmp trap link-status
!
cat35-L8-1#sh int gi0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is Gigabit Ethernet, address is 0005.313e.7581 (bia
0005.313e.7581)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s
input flow-control is off, output flow-control is on
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 12000 bits/sec, 14 packets/sec
905784 packets input, 1303109052 bytes, 0 no buffer
Received 66 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
1042863 packets output, 190194068 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
GigabitEthernet0/2 is up, line protocol is up
Hardware is Gigabit Ethernet, address is 0005.313e.7582 (bia
0005.313e.7582)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s
input flow-control is off, output flow-control is on
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 12000 bits/sec, 13 packets/sec
1486 packets input, 179522 bytes, 0 no buffer
Received 1421 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
1948976 packets output, 1493416902 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
==================================================================
De informatie opgenomen in dit bericht kan vertrouwelijk zijn en
is uitsluitend bestemd voor de geadresseerde. Indien u dit bericht
onterecht ontvangt wordt u verzocht de inhoud niet te gebruiken en
de afzender direct te informeren door het bericht te retourneren.
==================================================================
The information contained in this message may be confidential
and is intended to be exclusively for the addressee. Should you
receive this message unintentionally, please do not use the contents
herein and notify the sender immediately by return e-mail.
==================================================================
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=44333&t=44333
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
