If I understand you correctly, I don't think we were seeing what you're describing.
We had the problem I described even when all devices were attached to a single 3548. Also, someone else asked about the MAC addresses....they were all correct. Clearing MACs on the switch didn't help the issue. At 08:33 PM 12/21/2002 -0500, you wrote: >Craig, >This reminds me of a similar problem when I first got my 3550's where it >could ping one network but not another. I hope you don't see this when >you do upgrade to the 3550-EMI since you're in a production environment. > > >3550-A#config t >Enter configuration commands, one per line. End with CNTL/Z. >3550-A(config)#int vlan1 >3550-A(config-if)#ip add 192.168.10.2 255.255.255.0 >3550-A(config-if)#exit >3550-A(config)#ip default-gateway 192.168.10.1 >3550-A(config)#^Z >3550-A# >00:15:38: %SYS-5-CONFIG_I: Configured from console by console >3550-A#ping 192.168.10.1 > >Type escape sequence to abort. >Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds: >..... >Success rate is 0 percent (0/5) >3550-A#config t >Enter configuration commands, one per line. End with CNTL/Z. >3550-A(config)#int vlan1 >3550-A(config-if)#ip add 192.168.250.2 255.255.255.0 >3550-A(config-if)#exit >3550-A(config)#ip default-gateway 192.168.250.1 >3550-A(config)#^Z >3550-A# >00:16:19: %SYS-5-CONFIG_I: Configured from console by console >3550-A#ping 192.168.10.1 > >Type escape sequence to abort. >Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds: >!!!!! >Success rate is 100 percent (5/5), round-trip min/avg/max = 1/200/1000 >ms >3550-A#ping 192.168.250.1 > >Type escape sequence to abort. >Sending 5, 100-byte ICMP Echos to 192.168.250.1, timeout is 2 seconds: >!!!!! >Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms > > >3550-B(config-if)#int vlan 1 >3550-B(config-if)#ip add 192.168.0.2 255.255.255.0 >3550-B(config)#ip default-gateway 192.168.0.1 > >3550-B#ping 192.168.0.2 > >Type escape sequence to abort. >Sending 5, 100-byte ICMP Echos to 192.168.0.2, timeout is 2 seconds: >!!!!! >Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms >3550-B#ping 192.168.0.1 > >Type escape sequence to abort. >Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds: >..... > > >Enter configuration commands, one per line. End with CNTL/Z. >3550-B(config)#int vlan 1 >3550-B(config-if)#ip add 192.168.10.2 255.255.255.0 >3550-B(config)#ip default-gateway 192.168.10.1 > > >3550-B#ping 192.168.10.2 > >Type escape sequence to abort. >Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds: >!!!!! >Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms >3550-B#ping 192.168.10.1 > >Type escape sequence to abort. >Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds: >!!!!! >Success rate is 100 percent (5/5), round-trip min/avg/max = 1/200/1000 >ms >. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=59707&t=59682 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]