I think you need to add the command ip ospf network point-to-point to your spoke router.
Reza ""Arnaud V."" wrote in message news:[EMAIL PROTECTED] > Hello, > > I have an ospf problem. Two neighbors on a nbma > network who have connectivity are unable to go in the > two state, but have establish adjacency with the DR. > I include the configurations and ospf neighbor > states. > Perhaps have I done a mistake or don't know ospf > enough. Can u help please. > > Thanks in advance > > __________________________________________________ > Do you Yahoo!? > Yahoo! Tax Center - forms, calculators, tips, more > http://taxes.yahoo.com/ > R2 > > interface Serial1/0 > no ip address > encapsulation frame-relay IETF > no fair-queue > frame-relay traffic-shaping > frame-relay class R2-ts > ! > interface Serial1/0.1 point-to-point > ip address 150.50.24.1 255.255.255.252 > ip ospf message-digest-key 1 md5 cisco > frame-relay interface-dlci 204 > ! > interface Serial1/0.2 multipoint > ip address 150.50.100.1 255.255.255.224 > ip ospf message-digest-key 1 md5 cisco > ip ospf network non-broadcast > ip ospf priority 0 > frame-relay map ip 150.50.100.2 205 broadcast > frame-relay map ip 150.50.100.3 203 broadcast > ! > router ospf 1 > log-adjacency-changes > area 0 authentication message-digest > redistribute connected subnets > network 150.50.24.0 0.0.0.3 area 0 > network 150.50.100.0 0.0.0.127 area 0 > -------------------------------------------------------------------------- ------ > > ROUTERp1R2#sh ip ospf neigh > > Neighbor ID Pri State Dead Time Address Interface > 172.32.1.1 1 FULL/ - 00:00:38 150.50.24.2 Serial1/0.1 > N/A 0 ATTEMPT/DROTHER - 150.50.100.3 Serial1/0.2 > 5.5.5.5 255 FULL/DR 00:01:39 150.50.100.2 Serial1/0.2 > -------------------------------------------------------------------------- ------- > > ROUTERp1R2#sh ip ospf int > Serial1/0.1 is up, line protocol is up > Internet Address 150.50.24.1/30, Area 0 > Process ID 1, Router ID 2.2.2.2, Network Type POINT_TO_POINT, Cost: 48 > Transmit Delay is 1 sec, State POINT_TO_POINT, > Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 > Hello due in 00:00:02 > Index 1/1, flood queue length 0 > Next 0x0(0)/0x0(0) > Last flood scan length is 1, maximum is 6 > Last flood scan time is 0 msec, maximum is 0 msec > Neighbor Count is 1, Adjacent neighbor count is 1 > Adjacent with neighbor 172.32.1.1 > Suppress hello for 0 neighbor(s) > Message digest authentication enabled > Youngest key id is 1 > Serial1/0.2 is up, line protocol is up > Internet Address 150.50.100.1/27, Area 0 > Process ID 1, Router ID 2.2.2.2, Network Type NON_BROADCAST, Cost: 48 > Transmit Delay is 1 sec, State DROTHER, Priority 0 > Designated Router (ID) 5.5.5.5, Interface address 150.50.100.2 > No backup designated router on this network > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 > Hello due in 00:00:10 > Index 2/2, flood queue length 0 > Next 0x0(0)/0x0(0) > Last flood scan length is 1, maximum is 6 > Last flood scan time is 0 msec, maximum is 0 msec > Neighbor Count is 1, Adjacent neighbor count is 1 > Adjacent with neighbor 5.5.5.5 (Designated Router) > Suppress hello for 0 neighbor(s) > Message digest authentication enabled > Youngest key id is 1 > FastEthernet4/0 is up, line protocol is up > Internet Address 150.50.17.2/24, Area 3 > Process ID 1, Router ID 2.2.2.2, Network Type POINT_TO_MULTIPOINT, Cost: 1 > Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT, > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 > Hello due in 00:00:07 > Index 1/3, flood queue length 0 > Next 0x0(0)/0x0(0) > Last flood scan length is 0, maximum is 0 > Last flood scan time is 0 msec, maximum is 0 msec > Neighbor Count is 0, Adjacent neighbor count is 0 > Suppress hello for 0 neighbor(s) > R3 > > interface Serial2/0 > ip address 150.50.100.3 255.255.255.224 > encapsulation frame-relay IETF > ip ospf message-digest-key 1 md5 cisco > ip ospf priority 0 > clockrate 2015232 > frame-relay map ip 150.50.100.1 302 broadcast > frame-relay map ip 150.50.100.2 305 broadcast > frame-relay map ip 150.50.100.3 302 > no frame-relay inverse-arp > > router ospf 1 > log-adjacency-changes > area 0 authentication message-digest > network 150.50.100.0 0.0.0.127 area 0 > > -------------------------------------------------------------------------- ------- > routerp1R3#sh ip ospf neigh > > Neighbor ID Pri State Dead Time Address Interface > 2.2.2.2 0 INIT/DROTHER 00:00:57 150.50.100.1 Serial2/0 > 5.5.5.5 255 FULL/DR 00:01:48 150.50.100.2 Serial2/0 > > -------------------------------------------------------------------------- ------- > routerp1R3#sh ip ospf int > Serial2/0 is up, line protocol is up > Internet Address 150.50.100.3/27, Area 0 > Process ID 1, Router ID 3.3.3.3, Network Type NON_BROADCAST, Cost: 48 > Transmit Delay is 1 sec, State DROTHER, Priority 0 > Designated Router (ID) 5.5.5.5, Interface address 150.50.100.2 > No backup designated router on this network > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 > Hello due in 00:00:11 > Index 1/1, flood queue length 0 > Next 0x0(0)/0x0(0) > Last flood scan length is 1, maximum is 1 > Last flood scan time is 0 msec, maximum is 0 msec > Neighbor Count is 2, Adjacent neighbor count is 1 > Adjacent with neighbor 5.5.5.5 (Designated Router) > Suppress hello for 0 neighbor(s) > Message digest authentication enabled > Youngest key id is 1 > R5 > > interface Serial1/1 > ip address 150.50.100.2 255.255.255.224 > encapsulation frame-relay IETF > ip ospf message-digest-key 1 md5 cisco > ip ospf priority 255 > frame-relay de-group 1 502 > frame-relay map ip 150.50.100.1 502 broadcast > frame-relay map ip 150.50.100.2 502 > frame-relay map ip 150.50.100.3 503 broadcast > > router ospf 1 > log-adjacency-changes > area 0 authentication message-digest > area 4 nssa > network 9.9.9.0 0.0.0.255 area 4 > network 150.50.100.0 0.0.0.127 area 0 > neighbor 150.50.100.3 > neighbor 150.50.100.1 > > -------------------------------------------------------------------------- ------- > routerp1R5#sh ip ospf neigh > > Neighbor ID Pri State Dead Time Address Interface > 3.3.3.3 0 FULL/DROTHER 00:01:44 150.50.100.3 Serial1/1 > 2.2.2.2 0 FULL/DROTHER 00:01:36 150.50.100.1 Serial1/1 > -------------------------------------------------------------------------- ------- > > routerp1R5#sh ip ospf int > Serial1/1 is up, line protocol is up > Internet Address 150.50.100.2/27, Area 0 > Process ID 1, Router ID 5.5.5.5, Network Type NON_BROADCAST, Cost: 48 > Transmit Delay is 1 sec, State DR, Priority 255 > Designated Router (ID) 5.5.5.5, Interface address 150.50.100.2 > No backup designated router on this network > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5 > Hello due in 00:00:17 > Index 1/1, flood queue length 0 > Next 0x0(0)/0x0(0) > Last flood scan length is 1, maximum is 6 > Last flood scan time is 0 msec, maximum is 0 msec > Neighbor Count is 2, Adjacent neighbor count is 2 > Adjacent with neighbor 3.3.3.3 > Adjacent with neighbor 2.2.2.2 > Suppress hello for 0 neighbor(s) > Message digest authentication enabled > Youngest key id is 1 > Loopback2 is up, line protocol is up > Internet Address 9.9.9.1/24, Area 4 > Process ID 1, Router ID 5.5.5.5, Network Type LOOPBACK, Cost: 1 > Loopback interface is treated as a stub Host Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=64246&t=64176 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
