Mel Broadhurst wrote: >Michael Walters wrote: > > > >>Michael Walters wrote: >> >> >> >> >> >>>[EMAIL PROTECTED] wrote: >>> >>> >>> >>> >>> >>> >>> >>>>Hello All, >>>> >>>>I installed SimplyMEPIS-3.3.1 successfully on my hard drive. I had some >>>>trouble >>>>configuring Kmail, but that is not the reason I am going back to Libranet >>>>3.0. >>>> >>>>When I installed Mepis the Libranet installation was clobbered, which would >>>>have >>>>been all right if I could have booted into windows 95. >>>> >>>>But at least libranet detected windows 95 on drive c. >>>> >>>>Also the only mail client available in Mepis was Kmail. I had a choice of >>>>both >>>>Kmail and Mozilla Thunderbird in Libranet. >>>> >>>>I am sure glad that I did not ask for my money back for Libranet. I would >>>>like >>>>to have access to a few more applications like Thunderbird. >>>> >>>>I do not have time to reinstall Libranet 3.0 tonight or tomorrow before >>>>18:00. >>>>So I am using Mozilla firefox and web mail to do my email and firefox for >>>>browsing. >>>> >>>>I am sending this message with Mozilla firefox in Mepis through web mail. >>>> >>>>One thing about SimplyMEPIS is that it is an easier install. But I am going >>>>back >>>>to Libranet 3.0 on Tuesday. >>>> >>>>And I had a lot of fun trying out a new distribution. So all is not lost. >>>> >>>>I am going to a meeting tonight and will be away from home tomorrow until >>>>supper >>>>time. >>>> >>>>Regards, >>>> >>>>Michael Walters >>>> >>>> >>>> >>>> >>>>___________________________________________ >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>Hello everyone at clug-talk, >>> >>>I have my Libranet system up and running again. It did not take long to >>>configure Thunderbird to get mail. I still have to configure my filters. >>>But I can do those a little at a time. >>> >>>Regards, >>> >>>Michael Walters >>> >>>_______________________________ >>> >>> >>> >>> >>> >>> >>I am having difficulty in configuring my canon BJ-200e inkjet printer. I >>am using the printing configuration wizzard, and have gone to the >>configure printer help icon, but there is something I am not getting. >> >>I select canon, and then bj-200 and get canon on parallel port #1 and >>select US letter format and click on send test page a pop up says that I >>sent a test page to canon BJ-200, but the printer (which is on) does >>nothing. >> >>All help is appreciated in advance. >> >>While I am waiting for replies I will go to zap to it television to see >>what is on TV and will configure my filters so that I get my messages >>sorted. >> >>Regards, >> >>Michael Walters >> >>Michael: >> >> >> >> >If you are using Cups in Libranet, I believe your problem will be solved >by _not_ using the "canon on parallel port #1". Use instead the >"parallel port #1" by itself which you will find just below. I had the >same problem and this fixed it. > >Regards > >Mel Broadhurst > > >_______________________________________________ > > >
Hello Mel Broadhurst, I tried to do as you suggested but could not figure out how to selcect parallel port by itself. I removed the canon BJ-200 icon, but then got stuck. would it be possible some time this week end to come over to my place and figure this out for me? If you call 265-4364 on Friday 2005 June 17 around 6:00 P.M. I could give you directions. I do this because I do not want to give my street address over the internet, and I recognise your voice. Regards, Michael _______________________________________________ clug-talk mailing list [email protected] http://clug.ca/mailman/listinfo/clug-talk_clug.ca Mailing List Guidelines (http://clug.ca/ml_guidelines.php) **Please remove these lines when replying
