Nope Rich Knowles Indigo. LF38 Halifax
On 2012-11-16, at 12:39, "Gosse, Rob" <rob.go...@flyjazz.ca> wrote: Colonial auto parts I think? No fittings though. Burnside, just off Windmill road From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Rich C&C Sent: Friday, November 16, 2012 12:41 PM To: cnc-list@cnc-list.com Subject: Re: Stus-List Yanmar exhaust mix elbow pluggage question/survey Bob. That elbow is available for around $150 or less. I’ll get the info and post it. Rich. From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Robert Abbott Sent: November 16, 2012 12:29 To: Dennis C.; cnc-list@cnc-list.com Subject: Stus-List Yanmar exhaust mix elbow pluggage question/survey Dennis: I am in the process of replacing the SS wet exhaust muffler with a Vernalift and, since I am working in the small space, was considering replacing the whole mixing elbow assembly by removing the piece that bolts to the exhaust manifold. First, I will remove the 2" hose from the actual mixing elbow and try to look up inside to see the condition, if there is significant carbon buildup. Locally, this assembly will cost approx. $533 plus 15% tax. Below is something I recently read on a Yanmar site....might be helpful: 5. Carbon buildup The typical diesel engine usage by a sailboat owner is about the worst you can ask for. By typical I mean start her up, take her out to the first buoy, raise the sails and shut off that noisemaker. Same procedure in reverse on the way home. Also many hours of battery charging at medium speed and practically no load by a cruising sailor is hard on the engine. The Yanmar GM series engines are classified as a hi-revving, high compression engine. The max RPM is 3500 and the long term RPM is 3000. The bottom line is that the typical sailboat owner abuses the engine, which leads to carbon buildup in the cylinders, injectors and mixing elbow. In other words the diesel engine is happiest at high rpm under high load. What is the poor sailor to do? First of all, warm up the engine at least 10 minutes at the dock before leaving. Once under way, run her fast for as long as possible. Fast means 2500-3000 rpm. This will to some extent reduce carbon buildup. Unlike gasoline engines, you cannot blow out carbon buildup by extended hi-revving of the engine. Similarly once the engine is nice and hot, you need to idle her for 5-10 minutes so she can cool off before shutting her down. If for whatever reason you came chugging home at 1700 rpm, rev her up to 3000 rpm for a minute or so before going to idle for the cooldown period. If there is carbon buildup, it will be evident by rough idling. Take your injectors out and have them tested for spray pattern and injection pressure by a diesel shop. New injection nozzles are not as expensive as you think (about USD $60 each). The Yanmar manual also recommends inspecting the mixing elbow for carbon buildup every 300 hours. Just pull the exhaust tube off and look inside with a shaving mirror and flashlight. If the passage is more than 30% blocked, you need to remove the elbow and chip the carbon out with a screwdriver or old chisel. In my case I also got carbon buildup as a result of timing misalignment. The misalignment was caused by at least 2 “diesel gurus”, who re-installed the injection pump after pulling the gear case cover . Injection timing is controlled by brass shims between the pump and the gear case cover. INSIST on a timing check every time the injection pump is re-installed. Bob Abbott AZURA C&C 32 - 84 Halifax, N.S. On 2012/11/16 11:57 AM, Dennis C. wrote: I just cleaned the exhaust elbow on a Yanmar 2GM on a 29 MK? for a client for the second time in 3-4 years. I have other friends with Yanmars who have never had to clean the elbow. This 29 rarely motors longer than from the slip to the harbor entrance and back. The other boats sometimes motor long distances. I am just curious as to the root cause for the pluggage. Is it usage? Is it the model? For those listers that have frequent mix elbow pluggage, how do you use your Yanmar? Which Yanmar do you have? Do you motor for long periods or just to the harbor entrance and back? Could frequent short trips hasten pluggage? Does long periods of motoring prevent pluggage? Dennis C. Touche' 35-1 #83 Mandeville, LA _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com The information contained in this email is intended only for the individual or entity to whom it is addressed. Its contents (including any attachments) may contain confidential and/or privileged information. If you are not an intended recipient, you may not use, disclose, disseminate, copy or print its contents. If you received this email in error, please notify the sender by reply email and delete and destroy the message. L’information contenue dans ce courriel est destinée exclusivement aux personnes ou aux entités auxquelles le courriel est adressé. Le contenu de ce courriel (y compris toute pièce jointe) peut renfermer de l’information confidentielle et / ou privilégiée. Si ce message ne vous est pas destiné, vous ne pouvez utiliser, divulguer, diffuser, copier ou imprimer son contenu. Si vous avez reçu ce courriel par erreur, veuillez aviser l’expéditeur en lui faisant parvenir une réponse. De plus, veuillez supprimer et détruire le message. _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com