I'll 2nd the Kiwi Grip--easy to put on and the 'grip' can be varied easily, if desired, by the roller 'nap' and technique of rolling.
I had the yard put it on after my crew removed the hardware--first time for the yard doing it--and they were impressed. No issues yet going into my 3rd year with it. Charlie Nelson Water Phantom C&C 36 XL/kcb cenel...@aol.com -----Original Message----- From: Russ & Melody via CnC-List <cnc-list@cnc-list.com> To: Jim Watts <paradigmat...@gmail.com>; cnc-list <cnc-list@cnc-list.com> Sent: Fri, Feb 27, 2015 1:20 am Subject: Re: Stus-List Non-Slip Damn. The plan did seem a bit risky but I was looking forward to hear how it turned out. Cheers, Russ Sweet 35 mk-1 At 09:31 PM 26/02/2015, you wrote: I have one word. Kiwi Grip. OK, it's two. Sue me. Pressing a mold into rapidly curing gelcoat sounds like an incredibly painful thing to do to yourself. Jim Watts Paradigm Shift C&C 35 Mk III Victoria, BC On 26 February 2015 at 17:48, Paul Hood via CnC-List < cnc-list@cnc-list.com> wrote: I was wondering if anyone has ever ventured to do the following project that Iâm working through. I bought my boat from the original owner 2 years ago and am in the middle of redoing my non-slip.  I have removed all deck hardware with the exception of the toe rail, sanded down the existing non-slip so that all is smooth and am preparing to spray gelcoat over the entire deck. Once sprayed smooth, I will tape off areas for pattern and spread a layer of gelcoat followed immediately by the pressing of the Gibco flex mould to create the non-slip.  www.gibcoflexmold.com  I know this is different than the original roll-on finish, but I think the Gibco wears better, is easier to clean, is easier on bear skin, and looks much better to boot. My hope is that the grip is better than rolled as it is more consistent throughout. There are dozens of patterns and since Iâm not matching, Iâm getting the one claiming to have the best grip. It will be definitely better than current as the surface is chalked throughout and worn in many areas. In addition, there was a deck repair some years back and the color is visibly different and the surface below the non-slip repair is thin and almost see through.  Iâm waiting for this months -20c temperatures to move out before I start heating and spraying surface. Canadian winters .  Has anyone ever tackled such a project and if so, do you have any hints. Iâm sure there are lots of opinions here and I know Iâm about to open the can of worms on many levels but Iâd like to hear what you think.  Thanks, Paul Hood 1982 C&C34  _______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com _______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com _______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com