Thank you Frank.
From: Franklin Schenk via CnC-List <cnc-list@cnc-list.com> To: "cnc-list@cnc-list.com" <cnc-list@cnc-list.com>, Cc: Franklin Schenk <fdsch...@flash.net> Date: 05/09/2016 04:21 PM Subject: Re: Stus-List Stay Shroud Tension Sent by: "CnC-List" <cnc-list-boun...@cnc-list.com> I have used the following technique on many different boats without using a Loos gage. First, I check that the mast is straight athwartship (sideways) and that I have the desired rake which is different for each boat. I tighten the turnbuckles on the fore and aft stays first. I check the tension by pulling on them at about chest height. The stays should move no more than about one inch. The same applies to the upper shrouds. On boats that have only one lower, I tighten them until I can pull about 1 1/2 inches. On boats that have two lowers, I tighten the forward lowers until I can pull about 1 1/2 inches. On the aft lowers I use about 2 inches. The next step is to check the tension out under sail. First I make sure that the mast is straight. This will tell me if the lower shrouds are correct. There may be some slop on the downwind side depending on the wind speed. Adjusting rake is another procedure depending on the weather helm of the boat. Frank On Monday, May 9, 2016 1:22 PM, Bob Caughran via CnC-List <cnc-list@cnc-list.com> wrote: Chris, I do not use a Loos gage on Beemer, 29mkll, to tune my rig. My process is as follows. With all stays and shrouds lose, I tension the stays so I have approximately 9 inches rake along the boom using a weight on the main halyard. Forestay first, then backstay to remove slop. I them tension the upper shrouds to hand tight and using the main halyard on the toe rails to align the masthead. I then add two turns to the turnbuckles. Check masthead alignment again. Once all aligned, I tighten the lowers hand tight. Sight the mast to ensure straight. Add two turns to each lower. Sight the mast. Time for on the water final tune. In roughly 10-12 knots of wind on beem reach, look at leeward shrouds for play. Removed a third of the play tightening the leeward turnbuckles. Count and remember the number of turns. Tack boat. Tighten leeward turnbuckle same Number of turns as previous tack. And I tack back and forth checking and making any final adjustments. You'll want the slop out of the leeward shrouds. Sounds like a long process but it really isn't. Is using s Loos gage quicker? Yes but I'm a cheap son of a gun. And even with a Loos gage you'll still occasional on water adjustments. Bob Caughran Beemer, 29MKII, 309 Sent from my iPhone > On May 9, 2016, at 10:44 AM, Chris via CnC-List <cnc-list@cnc-list.com> wrote: > > > I have a C&C 24 was wondering if you know how many pounds of tension are > needed on all the lines that hold the mast in place? > > Sent from my iPhone >>> >> _______________________________________________ >> >> This list is supported by the generous donations of our members. If you > like what we do, please help us pay for our costs by donating. All > Contributions are greatly appreciated! > > > _______________________________________________ > > This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated! _______________________________________________ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated! _______________________________________________ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated!
_______________________________________________ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated!
