Scissor jack worked just fine for me. From: CnC-List <cnc-list-boun...@cnc-list.com> On Behalf Of Joel Aronson via CnC-List Sent: Friday, August 28, 2020 10:01 AM To: cnc-list <cnc-list@cnc-list.com> Cc: Joel Aronson <joel.aron...@gmail.com> Subject: Re: Stus-List 37+ Cruise Speed
I've heard of people using a basketball. FWIW Joel On Fri, Aug 28, 2020 at 9:51 AM Ken Heaton via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: Some people have had success putting something strong and inflatable under the engine to raise it, something like this: https://www.youtube.com/watch?v=PL1ST_gZbt4 Ken H. On Fri, 28 Aug 2020 at 10:32, John Conklin via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: David, I believe my vibration is also due to original Motor Mounts as well on my 1983 - 37. Any other tips on the replacing? I asked a mechanic and he said they needed a special tool to raise the engine? Also No idea how I am getting to back ones with out removing fuel tank Which is nice new plastic type but placed in starboard lazzarette making all entry to aft section rudder and motor Difficult Thanks! John Conklin S/V Halcyon S/V Heartbeat www.flirtingwithfire.com<http://www.flirtingwithfire.com> On Aug 24, 2020, at 12:45 PM, David Risch via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: Chuck...replaced my motor mounts my self. Not that hard. Unless that V drive makes it that hard. Sent from my Android. Please forgive typos. Thank you. ________________________________ From: CnC-List <cnc-list-boun...@cnc-list.com<mailto:cnc-list-boun...@cnc-list.com>> on behalf of Chuck Gilchrest via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> Sent: Monday, August 24, 2020 12:40:45 PM To: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com> <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> Cc: Chuck Gilchrest <csgilchr...@comcast.net<mailto:csgilchr...@comcast.net>> Subject: Re: Stus-List 37+ Cruise Speed Peter, My 1983 LF 35 came with a Yanmar 3HM with a 3 blade fixed prop. It’s happiest around 2200 RPM at roughly 6 knots. Anything more than that it sounds like the hull is shaking apart. Not a lot of sound deadening in general with that diesel, but it gets pretty loud at higher RPMs. Since I replaced the shaft, cutlass bearing, installed a dripless shaft seal when purchased 4 years ago, vibration is likely motor mounts which are probably original. Someday… Chuck Gilchrest Half Magic 1983 35 Landfall Padanaram, MA From: CnC-List <cnc-list-boun...@cnc-list.com<mailto:cnc-list-boun...@cnc-list.com>> On Behalf Of Peter Cowenhoven via CnC-List Sent: Monday, August 24, 2020 10:18 AM To: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com> Cc: Peter Cowenhoven <pscowenho...@yahoo.com<mailto:pscowenho...@yahoo.com>> Subject: Re: Stus-List 37+ Cruise Speed I've got a Westerbeke 33 with a 2 blade folding prop. I would say I do 7 knots at about 2700 -2800 rpm pretty consistently. Sent from Yahoo Mail on Android<https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature> On Tue, Jun 23, 2020 at 12:53 PM, Rob Hamlin via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: Hi What is everyone’s motor/ rpm optimal motoring speed? Thanks Rob Sent from my iPhone _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray _______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray -- Joel
_______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray