Hello, On Mon, Nov 24, 2008 at 9:07 PM, Joerg Lippmann <[EMAIL PROTECTED]> wrote:
I have 'auto usb0' first, then the rest of the lines are the same as yours > iface usb0 inet static > address 192.168.0.200 > netmask 255.255.255.0 > network 192.168.0.0 > up iptables -A POSTROUTING -t nat -j MASQUERADE -s 192.168.0.0/24 & > up echo 1 > /proc/sys/net/ipv4/ip_forward & > up iptables -P FORWARD ACCEPT & > down iptables -D POSTROUTING -t nat -j MASQUERADE -s 192.168.0.0/24 & > After plugging in the NEO, just > > sudo ifup usb0 Hmm, after I did a 'sudo idown usb0' first it works: [EMAIL PROTECTED]:~$ sudo ifup usb0 * Stopping NTP server ntpd [EMAIL PROTECTED]:~$ ...done. * Starting NTP server ntpd ...done. (the ntpd part looks scary) Hmm, when I replug my Freerunner, this is what happens: [EMAIL PROTECTED]:~$ ifconfig usb0 usb0 Link encap:Ethernet HWaddr 00:00:22:55:bb:00 inet6 addr: fe80::200:22ff:fe55:bb00/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1152 (1.1 KB) [EMAIL PROTECTED]:~$ sudo ifup usb0 ifup: interface usb0 already configured [EMAIL PROTECTED]:~$ ifconfig usb0 usb0 Link encap:Ethernet HWaddr 00:00:22:55:bb:00 inet6 addr: fe80::200:22ff:fe55:bb00/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1152 (1.1 KB) Huh? where did that IPv6 address come from? > > does the job quite fine. You may have to change /etc/resolv.conf on the NEO > manually. > > When you re-insert the NEO, just issue > > sudo ifdown usb0 && ifup usb0 I still don't know why the Freerunner gets a IPv6 address, but the above works: [EMAIL PROTECTED]:~$ sudo ifdown usb0 RTNETLINK answers: No such process [EMAIL PROTECTED]:~$ sudo ifup usb0 * Stopping NTP server ntpd [EMAIL PROTECTED]:~$ ...done. * Starting NTP server ntpd ...done. [EMAIL PROTECTED]:~$ ifconfig usb0 usb0 Link encap:Ethernet HWaddr 00:00:22:55:bb:00 inet addr:192.168.0.200 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::200:22ff:fe55:bb00/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:34 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:5558 (5.5 KB) > Hope it helps It did - many thanks! -- Regards, Torfinn Ingolfsen _______________________________________________ Openmoko community mailing list community@lists.openmoko.org http://lists.openmoko.org/mailman/listinfo/community