On Tue, 2001-11-13 at 14:35, Yves Duret wrote: > [EMAIL PROTECTED] (Robert Fox) writes: > > > No. Says "xsane: no devices available" > > > > Like I said, I was previously successful getting the Mustek 1200CU > > scanner to work using a patched sane-backend found on the internet. > > the latest sane includes those patch (aka mustek_usb). > > > The recent attempt is on a fresh Cooker install from last week. > > can you give me the output of > rpm -qa | grep sane
xsane-gimp-0.80-2mdk libsane1-1.0.5-3mdk sane-frontends-1.0.5-4mdk sane-backends-1.0.5-3mdk xsane-0.80-2mdk > rpm -q ldetect-lst drakxtools ldetect-lst-0.1.2-32mdk drakxtools-1.1.7-41mdk > in /etc/sane.d/mustek_usb.conf you have only one line with > usb 0x055f 0x0001 YES > and you should have an line with mustek_usb in /etc/sane.d/dll.conf YES > and finally the output of cat /proc/bus/usb/devices (is from this file taht > comes the 0x055f 0x0001 numbers.. i had perhaps a bad value in the DB). > thx > -- T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 11/900 us ( 1%), #Int= 1, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=d000 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 4 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=058f ProdID=9254 Rev= 1.00 S: Manufacturer=ALCOR S: Product=Generic USB Hub C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=255ms T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 11/900 us ( 1%), #Int= 1, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=d400 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=055f ProdID=0001 Rev= 1.00 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 64mA I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=usbscanner E: Ad=01(O) Atr=02(Bulk) MxPS= 2 Ivl= 0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl= 1ms Hope this helps!! R. Fox