Hi Uday, from the second log you send me (with Rudy's UBL) it looks like everything is fine except that the (hardwired) third level Boot Loader (U-boot) is not found. As I sayed before my program is only an (internal) test tool and far away from a real program. Check the source for filenames / pathes used.
Ciao, Peter On Thu, 21 Dec 2006, Uday Bhide wrote: > Hi Peter, > > Thanks for the guidance. > I tried the windows code that you sent. The communication with the UART > was fine. But a problem came up with the UBL that I tried to send. > I even tried sending Rudy's r-boot from the archives. I could get to the > r-boot prompt on hyper-terminal. > > This is the log of load.c program when I sent NAND UBL: > > > U:\davinci\UART>Uart-U.exe ubl_nand.bin 2 > read 14336 bytes from ubl_nand.bin > Waiting for boot message from Davinci > . BOOTME > sending ACK > Waiting for begin message from Davinci > BEGINsending empty CRC table > Waiting for done message from Davinci > DONESending data > Waiting for done message from Davinci > DONEWaiting for UBL message from Davinci > > Booting PSP Boot Loader > > Starting NAND Copy > > NAND Boot failed. Starting UART > BOOTPSP timed out > > > Note that I already have bootable u-boot in NAND flash. But I want to use > UART boot. > > > This is the log of load.c program when I sent Rudy's r-boot: > > > U:\davinci\UART>Uart-U.exe rboot.bin 2 > read 3000 bytes from rboot.bin > Waiting for boot message from Davinci > . BOOTME > sending ACK > Waiting for begin message from Davinci > BEGINsending empty CRC table > Waiting for done message from Davinci > DONESending data > Waiting for done message from Davinci > DONEWaiting for UBL message from Davinci > ee > Rboot->u-boot not found > > > Then I got to the r-boot prompt on hyper-terminal. Tried "?" and > got the help message. Could display memory using "d". > Then tried "l" (load into memory). Then there was no response. > As if the console was hung. > > I think I now need to send u-boot.bin. how should I send this ? As a ASCII > TEXT ? > > Right now, I'm clueless about how to proceed. Could you please > guide me more? > > Thank you. > Uday. > > > > > On 12/20/06, Peter Wippich <[EMAIL PROTECTED]> wrote: > > > > > > Hi, > > > > there was a very good basic introduction from Rudy posted to the list > > on July 28, please check the archive. > > > > Rudy alos provided a first stage bootloader later on. Can be found in the > > archives, too. > > > > Attached is a very crude little (Windows) program which implements a UART > > boot. Requires Rudy's first stage loader. Don't view this as a real > > program but more as a proof of function. > > > > Ciao, > > > > Peter > > > > > > > > > > On Wed, 20 Dec 2006, Uday Bhide wrote: > > > > > Hi all, > > > > > > I've just started working on the DaVinci EVM board > > > and I'm new to this mailing list too. > > > I read through a lot of mails from the mailing list but > > > could not get to the basics of what I need to know now. > > > > > > I need to utilize the UART boot to load a file to boot > > > the DSP. > > > > > > When I switch to the UART Boot mode and switch on > > > the board, the only thing I see on the minicom console > > > is "BOOTME BOOTME..." repeatedly. > > > > > > How do I start the UART communication? How to send > > > ACK to the RBL in the first hand? And what next? > > > > > > Can anybody who has a fair knowledge of the procedure > > > please send me the steps? > > > Also, please send any scripts or applications that can do > > > the necessary communication to send the UBL to the RAM. > > > > > > > > > Thanking you in advance, > > > Uday. > > > > > > > > > | Peter Wippich Voice: +49 30 46776411 | > > | G&W Instruments GmbH fax: +49 30 46776419 | > > | Gustav-Meyer-Allee 25, Geb. 12 Email: [EMAIL PROTECTED] | > > | D-13355 Berlin / Germany | > > > > > > > | Peter Wippich Voice: +49 30 46776411 | | G&W Instruments GmbH fax: +49 30 46776419 | | Gustav-Meyer-Allee 25, Geb. 12 Email: [EMAIL PROTECTED] | | D-13355 Berlin / Germany | _______________________________________________ Davinci-linux-open-source mailing list Davinci-linux-open-source@linux.davincidsp.com http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source