I am configuring an inherited DS20 with a SAN fiber network based on HSG80. If i use Fabric topology with a 8-EL fiber switch, i cant see the HSG units. For testing purposes, i have connected the HBA ang HSG directly without switch. If i configure HSG ports as arbitrated-loop, i can see and use volumes. Back to FABRIC topology, from srm console, i can see the units:
P00>>>wwidmgr -show wwid [0] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-0007 (ev:none) [1] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-0008 (ev:none) [2] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-0009 (ev:none) [3] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-000a (ev:none) [4] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-000b (ev:none) [5] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-000c (ev:none) But when i boot the debian testing os, the units are missing: mail:~# cat /proc/scsi/scsi Attached devices: Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: COMPAQ Model: BF00963643 Rev: 3B05 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: COMPAQ Model: BF00963643 Rev: 3B05 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 02 Lun: 00 Vendor: COMPAQ Model: BF00963643 Rev: 3B05 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 03 Lun: 00 Vendor: COMPAQ Model: BF00963643 Rev: 3B05 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 04 Lun: 00 Vendor: COMPAQ Model: BF00963643 Rev: 3B05 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 05 Lun: 00 Vendor: COMPAQ Model: BF00963643 Rev: 3B05 Type: Direct-Access ANSI SCSI revision: 02 There are all local scsi disks The module is loaded: mail:~# lsmod|grep lpfc lpfc 220760 0 scsi_transport_fc 44708 1 lpfc Here are the relevant part of dmesg: . . Emulex LightPulse Fibre Channel SCSI driver 8.1.9 Copyright(c) 2004-2006 Emulex. All rights reserved. scsi0 : on PCI bus 00 device 48 irq 23 ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) lpfc 0000:00:09.0: 0:1303 Link Up Event x1 received Data: x1 x0 x0 x0 . . It looks to me that the SAN network is working (i can see volumes from SRM) but something is wrong with lpfc driver or scsi_transport_fc. According to emulex information about lpfc module, there are some tools, like lputil, that are missing in the debian installation. There is no lpfc driver for alpha architecture in the manufacturer site. Has anybody succesfuly compiled the sources in alpha. Any help welcome. Thanks -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
