Resolved: An update to the HBA (Emulex LP8000) firmware resolved the issue. Resuming: To get working a DS20 with a HSG80 i have updated de SRM firmware, the HBA firmware and the 8-EL switch firmware..
acon ha escrito: > I am configuring an inherited DS20 with a SAN fiber network based on > HSG80. > If i use Fabric topology with a 8-EL fiber switch, i cant see the HSG > units. > For testing purposes, i have connected the HBA ang HSG directly without > switch. If i configure HSG ports as arbitrated-loop, i can see and use > volumes. > Back to FABRIC topology, from srm console, i can see the units: > > P00>>>wwidmgr -show wwid > [0] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-0007 > (ev:none) > [1] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-0008 > (ev:none) > [2] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-0009 > (ev:none) > [3] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-000a > (ev:none) > [4] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-000b > (ev:none) > [5] UDID:-1 WWID:01000010:6000-1fe1-0011-9ca0-0009-1150-1974-000c > (ev:none) > > But when i boot the debian testing os, the units are missing: > > mail:~# cat /proc/scsi/scsi > Attached devices: > Host: scsi1 Channel: 00 Id: 00 Lun: 00 > Vendor: COMPAQ Model: BF00963643 Rev: 3B05 > Type: Direct-Access ANSI SCSI revision: 02 > Host: scsi1 Channel: 00 Id: 01 Lun: 00 > Vendor: COMPAQ Model: BF00963643 Rev: 3B05 > Type: Direct-Access ANSI SCSI revision: 02 > Host: scsi1 Channel: 00 Id: 02 Lun: 00 > Vendor: COMPAQ Model: BF00963643 Rev: 3B05 > Type: Direct-Access ANSI SCSI revision: 02 > Host: scsi1 Channel: 00 Id: 03 Lun: 00 > Vendor: COMPAQ Model: BF00963643 Rev: 3B05 > Type: Direct-Access ANSI SCSI revision: 02 > Host: scsi1 Channel: 00 Id: 04 Lun: 00 > Vendor: COMPAQ Model: BF00963643 Rev: 3B05 > Type: Direct-Access ANSI SCSI revision: 02 > Host: scsi1 Channel: 00 Id: 05 Lun: 00 > Vendor: COMPAQ Model: BF00963643 Rev: 3B05 > Type: Direct-Access ANSI SCSI revision: 02 > > There are all local scsi disks > > The module is loaded: > mail:~# lsmod|grep lpfc > lpfc 220760 0 > scsi_transport_fc 44708 1 lpfc > > Here are the relevant part of dmesg: > > . > . > Emulex LightPulse Fibre Channel SCSI driver 8.1.9 > Copyright(c) 2004-2006 Emulex. All rights reserved. > scsi0 : on PCI bus 00 device 48 irq 23 > ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver > (PCI) > lpfc 0000:00:09.0: 0:1303 Link Up Event x1 received Data: x1 x0 x0 x0 > . > . > > It looks to me that the SAN network is working (i can see volumes from > SRM) but something is wrong with lpfc driver or scsi_transport_fc. > > According to emulex information about lpfc module, there are some > tools, like lputil, that are missing in the debian installation. There > is no lpfc driver for alpha architecture in the manufacturer site. > Has anybody succesfuly compiled the sources in alpha. > > Any help welcome. > > Thanks > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
