Actually, I just remembered that 4.4 kernel will try to load both the old and the new module (but without allhwsupport), so please try the following:
rmmod mv_cesa rmmod marvell_cesa modprobe marvell_cesa allhwsupport=1 dmesg | grep -i cesa Sorry for the confusion Jan On Mon, Feb 15, 2016 at 11:26 AM, JM <fi...@archlinux.us> wrote: > Thanks for the reply. Can you paste your /proc/crypto as well? > > Thanks, > Jan > > On Mon, Feb 15, 2016 at 11:25 AM, Rick Thomas <rbtho...@pobox.com> wrote: >>> Here you go... >>> >>>> root@sheeva:~# rmmod mv_cesa >>>> root@sheeva:~# modprobe marvell_cesa allhwsupport=1 >>>> root@sheeva:~# dmesg | tail -n 20 >>>> [ 16.730426] systemd[1]: Mounted Debug File System. >>>> [ 16.756783] systemd[1]: Started Load Kernel Modules. >>>> [ 16.776948] systemd[1]: Started Create list of required static device >>>> nodes for the current kernel. >>>> [ 16.804146] systemd[1]: Started LSB: Set console font and keymap. >>>> [ 17.023950] systemd[1]: Started Journal Service. >>>> [ 18.514731] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro >>>> [ 19.804133] orion_wdt: Initial timeout 21 sec >>>> [ 19.848469] MV-CESA:Could not register sha1 driver >>>> [ 19.848485] MV-CESA:Could not register hmac-sha1 driver >>>> [ 20.379009] systemd-journald[180]: Received request to flush runtime >>>> journal from PID 1 >>>> [ 20.386082] sd 0:0:0:0: Attached scsi generic sg0 type 0 >>>> [ 20.386886] ses 0:0:0:1: Attached scsi generic sg1 type 13 >>>> [ 21.518406] EXT4-fs (mmcblk0p1): mounting ext2 file system using the >>>> ext4 subsystem >>>> [ 21.682097] EXT4-fs (mmcblk0p1): mounted filesystem without journal. >>>> Opts: (null) >>>> [ 22.402713] Adding 9764860k swap on /dev/mapper/sheeva-swap. >>>> Priority:-1 extents:1 across:9764860k FS >>>> [ 22.938703] EXT4-fs (dm-2): mounted filesystem with ordered data mode. >>>> Opts: (null) >>>> [ 23.631978] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready >>>> [ 27.662122] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 >>>> Mb/s, full duplex, flow control disabled >>>> [ 27.662180] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready >>>> [ 37.350057] warning: process `colord-sane' used the deprecated sysctl >>>> system call with 8.1.2. >>>> root@sheeva:~# uname -a >>>> Linux sheeva 4.4.0-trunk-marvell #1 Debian 4.4.1-1~exp1 (2016-02-10) >>>> armv5tel GNU/Linux >>>> root@sheeva:~# >>> >>> For what it's worth, the system boots fine and appears to run OK with the >>> 4.4 kernel. >>> >>> Hope it helps! >>> >>> Rick >> >> A bit more info, incase it helps... >> >> Rick >> >>> root@sheeva:~# cat /proc/cpuinfo >>> processor : 0 >>> model name : Feroceon 88FR131 rev 1 (v5l) >>> BogoMIPS : 1185.79 >>> Features : swp half thumb fastmult edsp >>> CPU implementer : 0x56 >>> CPU architecture: 5TE >>> CPU variant : 0x2 >>> CPU part : 0x131 >>> CPU revision : 1 >>> >>> Hardware : Marvell Kirkwood (Flattened Device Tree) >>> Revision : 0000 >>> Serial : 0000000000000000 >>> root@sheeva:~#