Package: u-boot-sunxi Severity: critical Dear Maintainer,
after a fresh install of Debian "bullseye" the first reboot got stuck after "Starting kernel ..." It turend out that booting the system got always stuck using the a "normal" u-boot boot sequence. Using extlinux or FIT-Images is not affected. boot.scr : FAIL extlinux : OK FIT-Image: OK Since the Debian Installer provides neither extlinux configuration nor build a FIT-Image the system is unusable after the reboot from the installer. I got into the same situation during an update on an other system to bullseye. Bootlog: ---8<--- U-Boot SPL 2020.10+dfsg-1+b1 (Nov 19 2020 - 03:18:11 +0000) DRAM: 1024 MiB Trying to boot from MMC2 NOTICE: BL31: v2.3(): NOTICE: BL31: Built : 05:17:48, Oct 18 2020 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x4093968, model: Olimex A64-Olinuxino-eMMC INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP803 on RSB INFO: PMIC: Enabling DRIVEVBUS INFO: PMIC: dcdc1 voltage: 3.300V INFO: PMIC: dcdc5 voltage: 1.360V INFO: PMIC: dcdc6 voltage: 1.100V INFO: PMIC: dldo1 voltage: 3.300V INFO: PMIC: dldo2 voltage: 3.300V INFO: PMIC: dldo3 voltage: 2.800V INFO: PMIC: dldo4 voltage: 3.300V INFO: PMIC: fldo1 voltage: 1.200V INFO: PMIC: Enabling DC SW INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 843419 was applied INFO: BL31: cortex_a53: CPU workaround for 855873 was applied NOTICE: PSCI: System suspend is unavailable INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9 alloc space exhausted U-Boot 2020.10+dfsg-1+b1 (Nov 19 2020 - 03:18:11 +0000) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Olimex A64-Olinuxino-eMMC DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 1:1... In: serial Out: serial Err: serial Net: phy interface7 eth0: ethernet@1c30000 starting USB... Bus usb@1c1a000: USB EHCI 1.00 Bus usb@1c1a400: USB OHCI 1.0 Bus usb@1c1b000: USB EHCI 1.00 Bus usb@1c1b400: USB OHCI 1.0 scanning bus usb@1c1a000 for devices... 1 USB Device(s) found scanning bus usb@1c1a400 for devices... 1 USB Device(s) found scanning bus usb@1c1b000 for devices... 1 USB Device(s) found scanning bus usb@1c1b400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:1... Found U-Boot script /boot.scr 2225 bytes read in 2 ms (1.1 MiB/s) ## Executing script at 4fc00000 22744944 bytes read in 1003 ms (21.6 MiB/s) 28403 bytes read in 5 ms (5.4 MiB/s) 30071341 bytes read in 1326 ms (21.6 MiB/s) Booting Debian 5.9.0-2-arm64 from mmc 1:1... Moving Image from 0x40080000 to 0x40200000, end=41850000 ## Flattened Device Tree blob at 4fa00000 Booting using the fdt blob at 0x4fa00000 EHCI failed to shut down host controller. Loading Ramdisk to 48352000, end 49fffa2d ... OK Loading Device Tree to 0000000048348000, end 0000000048351ef2 ... OK Starting kernel ... ---8<--- Regards Benedikt Spranger