Hi,
I tried to install one (of two) L2000-36 (both running fine with
HPUX 11.11, ioscan below) with Linux on a seperate disk.
I tried to install using debian-40r0-hppa-netinst.iso
(CD was verified, md5sum taken from CD matches the md5sum
on the webpage)
Both systems fail after (log below)
Freeing unused kernel memory
Then I tried booting the netboot image from
http://www.debian.org/devel/debian-installer/
http://people.debian.org/~kyle/d-i/hppa/daily/
again both fail at similar place.
logfile from cdboot
Firmware Version 41.39
Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State CoProcessor State Cache Size
Number State Inst Data
--------- -------- --------------------- ----------------- ------------
0 360 MHz Active Functional 512 KB 1 MB
1 360 MHz Idle Functional 512 KB 1 MB
2 360 MHz Idle Functional 512 KB 1 MB
3 360 MHz Idle Functional 512 KB 1 MB
Central Bus Speed (in MHz) : 82
Available Memory : 1048576 KB
Good Memory Required : 16580 KB
Primary boot path: 0/0/1/1.2
Alternate boot path: 0/0/2/0.2
Console path: 0/0/4/0.0
Keyboard path: 0/0/4/0.0
Searching for device(s) with bootable media
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path# Device Path (dec) Device Path (mnem) Device Type and Utilities
----- ----------------- ------------------ -------------------------
P0 0/0/0/0 lan.10.2.1.8 LAN Module
IPL
P1 0/0/1/1.2 intscsib.2 Random access media
IPL
P2 0/0/2/1.2 media.2 Random access media
IPL
Enter Path Number or Device Path to continue boot sequence. Enter NO to go
to main menu.
> p2
Interact with IPL (Y, N, or Cancel)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
palo ipl 1.14 [EMAIL PROTECTED] Sat Apr 8 16:08:16 EDT 2006
Boot image contains:
0/vmlinux32 4190085 bytes @ 0xd08800
0/vmlinux64 5796516 bytes @ 0x781000
0/ramdisk 4468640 bytes @ 0x335000
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).
Command line for kernel: 'root=/dev/ram ramdisk_size=12580' console=ttyS0
TERM=vt102 palo_kernel=0'0/vmlinux'
Selected kernel: '0/vmlinux from partition 0
Selected ramdisk: /ramdisk from partition 0
Warning: kernel name doesn't end with 32 or 64 -- Guessing... Choosing 64-bit
kernelELF64 executable
Entry 00100000 first 00100000 n 3
Segment 0 load 00100000 size 3850240 mediaptr 0x1000
Segment 1 load 00504000 size 383288 mediaptr 0x3ad000
Segment 2 load 00564000 size 381062 mediaptr 0x40b000
Loading ramdisk 4468640 bytes @ 3fbac000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
Linux version 2.6.18-4-parisc64 (Debian 2.6.18.dfsg.1-11) ([EMAIL PROTECTED]) (gcc version 4.1.2 20061115 (prerelease)
(Debian 4.1.1-21)) #1 Wed Feb 21 10:20:02 MST 2007
FP[0] enabled: Rev 1 Model 16
The 64-bit Kernel has started...
Initialized PDC Console for debugging.
Determining PDC firmware type: 64 bit PAT.
model 00005c50 00000491 00000000 00000002 08ef50ff 100000f0 00000008 000000b2
000000b2
vers 00000301
CPUID vers 17 rev 11 (0x0000022b)
capabilities 0x1
model 9000/800/L2000-36
Total Memory: 1024 MB
initrd: 4fbac000-4ffeefa0
initrd: reserving 3fbac000-3ffeefa0 (mem_max 40000000)
Built 1 zonelists. Total pages: 262144
Kernel command line: root=/dev/ram ramdisk_size=12580' console=ttyS0 TERM=vt102
palo_kernel=0'0/vmlinux
PID hash table entries: 4096 (order: 12, 32768 bytes)
start_kernel(): bug: interrupts were enabled early
Console: colour dummy device 160x64
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 1048576k available
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
checking if image is initramfs... it is
Freeing initrd memory: 4363k freed
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. Rhapsody 360 at 0xfffffffffffa0000 [160] { 0, 0x0, 0x5c5, 0x00004 }
2. Rhapsody 360 at 0xfffffffffffa2000 [162] { 0, 0x0, 0x5c5, 0x00004 }
3. Rhapsody 360 at 0xfffffffffffa4000 [164] { 0, 0x0, 0x5c5, 0x00004 }
4. Rhapsody 360 at 0xfffffffffffa6000 [166] { 0, 0x0, 0x5c5, 0x00004 }
5. Memory at 0xfffffffffed08000 [8] { 1, 0x0, 0x095, 0x00009 }
6. Astro BC Runway Port at 0xfffffffffed00000 [0] { 12, 0x0, 0x582, 0x0000b }
7. Elroy PCI Bridge at 0xfffffffffed30000 [0/0] { 13, 0x0, 0x782, 0x0000a }
8. Elroy PCI Bridge at 0xfffffffffed32000 [0/1] { 13, 0x0, 0x782, 0x0000a }
9. Elroy PCI Bridge at 0xfffffffffed34000 [0/2] { 13, 0x0, 0x782, 0x0000a }
10. Elroy PCI Bridge at 0xfffffffffed36000 [0/3] { 13, 0x0, 0x782, 0x0000a }
11. Elroy PCI Bridge at 0xfffffffffed38000 [0/4] { 13, 0x0, 0x782, 0x0000a }
12. Elroy PCI Bridge at 0xfffffffffed3a000 [0/5] { 13, 0x0, 0x782, 0x0000a }
13. Elroy PCI Bridge at 0xfffffffffed3c000 [0/6] { 13, 0x0, 0x782, 0x0000a }
14. Elroy PCI Bridge at 0xfffffffffed3e000 [0/7] { 13, 0x0, 0x782, 0x0000a }
Enabling PDC_PAT chassis codes support v0.05
********** VIRTUAL FRONT PANEL **********
System Boot detected
*****************************************
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH OFF ON ON
LED State: Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
processor system initialization 1C00
*****************************************
************ EARLY BOOT VFP *************
End of early boot detected
*****************************************
Elroy version TR3.0 (0x4) found at 0xfffffffffed3a000
allocation failed: out of vmalloc space - use vmalloc=<size> to increase size.
Elroy version TR3.0 (0x4) found at 0xfffffffffed3c000
allocation failed: out of vmalloc space - use vmalloc=<size> to increase size.
Elroy version TR3.0 (0x4) found at 0xfffffffffed3e000
allocation failed: out of vmalloc space - use vmalloc=<size> to increase size.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Chassis warnings not supported.
unwind_init: start = 0x103e7520, end = 0x1040cf40, entries = 9634
Performance monitoring counters enabled for Rhapsody 360
audit: initializing netlink socket (disabled)
audit(1180701268.418:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PDC Stable Storage facility v0.30
Soft power switch support not available.
STI GSC/PCI core graphics driver Version 0.9a
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
0000:00:04.0: ttyS0 at MMIO 0xfffffffff8000000 (irq = 69) is a 16550A
0000:00:04.0: ttyS1 at MMIO 0xfffffffff8000008 (irq = 69) is a 16550A
0000:00:04.0: ttyS2 at MMIO 0xfffffffff8000010 (irq = 69) is a 16550A
0000:00:05.0: ttyS3 at MMIO 0xfffffffff8006000 (irq = 70) is a 16550A
Couldn't register serial port 0000:00:05.0: -28
RAMDISK driver initialized: 16 RAM disks of 12580K size 1024 blocksize
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory:
********** VIRTUAL FRONT PANEL **********
System Boot detected
*****************************************
LEDs: RUN ATTENTION FAULT REMOTE POWER
ON FLASH OFF ON ON
LED State: There was a system interruption that did not take the system down.
Check Chassis and Console Logs for error messages.
processor system initialization 1C00
*****************************************
************ EARLY BOOT VFP *************
End of early boot detected
*****************************************
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002)
tulip0: no phy info, aborting mtable build
tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1.
eth0: Digital DS21142/43 Tulip rev 65 at Port 0x80, 00:10:83:FC:42:A3, IRQ 65.
********** VIRTUAL FRONT PANEL **********
System Boot detected
*****************************************
LEDs: RUN ATTENTION FAULT REMOTE POWER
ON FLASH FLASH ON ON
LED State: System Running. Unexpected Reboot. Non-critical Error Detected.
Check Chassis and Console Logs for error messages.
processor system panic 1B00
*****************************************
************ EARLY BOOT VFP *************
End of early boot detected
*****************************************
********** VIRTUAL FRONT PANEL **********
System Boot detected
*****************************************
LEDs: RUN ATTENTION FAULT REMOTE POWER
ON FLASH FLASH ON ON
LED State: System Running. Unexpected Reboot. Non-critical Error Detected.
Check Chassis and Console Logs for error messages.
processor system panic 1B00
------------------
here an ioscan from running hpux:
# ioscan -fk
Class I H/W Path Driver S/W State H/W Type Description
===========================================================================
root 0 root CLAIMED BUS_NEXUS
ioa 0 0 sba CLAIMED BUS_NEXUS System Bus
Adapter (582)
ba 0 0/0 lba CLAIMED BUS_NEXUS Local PCI Bus
Adapter (782)
lan 0 0/0/0/0 btlan CLAIMED INTERFACE HP PCI
10/100Base-TX Core
ext_bus 0 0/0/1/0 c720 CLAIMED INTERFACE SCSI C896 Fast
Wide LVD
target 0 0/0/1/0.7 tgt CLAIMED DEVICE
ctl 0 0/0/1/0.7.0 sctl CLAIMED DEVICE Initiator
ext_bus 1 0/0/1/1 c720 CLAIMED INTERFACE SCSI C896 Fast
Wide Single-Ended
target 1 0/0/1/1.2 tgt CLAIMED DEVICE
disk 0 0/0/1/1.2.0 sdisk CLAIMED DEVICE COMPAQ
BD01864552
target 2 0/0/1/1.7 tgt CLAIMED DEVICE
ctl 1 0/0/1/1.7.0 sctl CLAIMED DEVICE Initiator
ext_bus 2 0/0/2/0 c720 CLAIMED INTERFACE SCSI C87x Fast
Wide Single-Ended
target 3 0/0/2/0.2 tgt CLAIMED DEVICE
disk 1 0/0/2/0.2.0 sdisk CLAIMED DEVICE COMPAQ
BD01864552
target 4 0/0/2/0.7 tgt CLAIMED DEVICE
ctl 2 0/0/2/0.7.0 sctl CLAIMED DEVICE Initiator
ext_bus 3 0/0/2/1 c720 CLAIMED INTERFACE SCSI C87x Fast
Wide Single-Ended
target 5 0/0/2/1.2 tgt CLAIMED DEVICE
disk 2 0/0/2/1.2.0 sdisk CLAIMED DEVICE HP DVD-ROM
304
target 6 0/0/2/1.7 tgt CLAIMED DEVICE
ctl 3 0/0/2/1.7.0 sctl CLAIMED DEVICE Initiator
tty 0 0/0/4/0 asio0 CLAIMED INTERFACE PCI Serial
(103c1048)
tty 1 0/0/5/0 asio0 CLAIMED INTERFACE PCI Serial
(103c1048)
ba 1 0/1 lba CLAIMED BUS_NEXUS Local PCI Bus
Adapter (782)
ba 2 0/2 lba CLAIMED BUS_NEXUS Local PCI Bus
Adapter (782)
ext_bus 4 0/2/0/0 c720 CLAIMED INTERFACE SCSI C87x Fast
Wide Differential
target 7 0/2/0/0.7 tgt CLAIMED DEVICE
ctl 4 0/2/0/0.7.0 sctl CLAIMED DEVICE Initiator
ba 3 0/3 lba CLAIMED BUS_NEXUS Local PCI Bus
Adapter (782)
lan 1 0/3/0/0 btlan CLAIMED INTERFACE HP
A5230A/B5509BA PCI 10/100Base-TX Addon
ba 4 0/4 lba CLAIMED BUS_NEXUS Local PCI Bus
Adapter (782)
lan 2 0/4/0/0 btlan CLAIMED INTERFACE HP
A5230A/B5509BA PCI 10/100Base-TX Addon
ba 5 0/5 lba CLAIMED BUS_NEXUS Local PCI Bus
Adapter (782)
ext_bus 5 0/5/0/0 c720 CLAIMED INTERFACE SCSI C87x Fast
Wide Differential
target 8 0/5/0/0.7 tgt CLAIMED DEVICE
ctl 5 0/5/0/0.7.0 sctl CLAIMED DEVICE Initiator
ba 6 0/6 lba CLAIMED BUS_NEXUS Local PCI Bus
Adapter (782)
lan 3 0/6/0/0 btlan CLAIMED INTERFACE HP A3738A PCI
10/100Base-TX Ultimate Combo
ba 7 0/7 lba CLAIMED BUS_NEXUS Local PCI Bus
Adapter (782)
fc 0 0/7/0/0 td CLAIMED INTERFACE HP Tachyon TL/TS
Fibre Channel Mass Storage Adapter
fcp 0 0/7/0/0.8 fcp CLAIMED INTERFACE FCP Protocol
Adapter
memory 0 8 memory CLAIMED MEMORY Memory
processor 0 160 processor CLAIMED PROCESSOR Processor
processor 1 162 processor CLAIMED PROCESSOR Processor
processor 2 164 processor CLAIMED PROCESSOR Processor
processor 3 166 processor CLAIMED PROCESSOR Processor
# uname -a
HP-UX lego2 B.11.11 U 9000/800 149901567 unlimited-user license
Any ideas welcome. The systems are rack mounted so removing HW
is not that easy
Christian
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]