Douglas,
Novidades, Compilei o driver hpt37x2.o aqui e o carreguei durante o boot, para isso copiei o arquivo hpt37x2.o para /lib/modules/2.4.19/kernel/drivers/scsi, com isso ele aparece no #modconf Installing module hpt37x2. If the device isn't there, or isn't configured correctly, this could cause your system to pause for up to a minute. Warning: loading /lib/modules/2.4.19/kernel/drivers/scsi/hpt37x2.o will taint the kernel: no license Installation succeeded. dei um lsmod thor:/home/thiagomz# lsmod Module Size Used by Tainted: P hpt37x2 55584 0 (unused) <-- Carregou ! ext3 56832 2 (autoclean) jbd 36344 2 (autoclean) [ext3] vga16fb 8800 0 (unused) fbcon-vga-planes 3168 0 [vga16fb] nvidia 1545248 10 ntfs 49536 0 (unused) ide-scsi 7680 0 Mas durante o boot.... #isso é normal ? HPT372: IDE controller on PCI bus 00 dev 98 HPT372: detected chipset, but driver not compiled in! HPT372: chipset revision 5 HPT372: not 100% native mode: will probe irqs later . . . #Nesta parte o boot fica super lento dando esses erros ! de lost interrupt hda: 39179952 sectors (20060 MB) w/2048KiB Cache, CHS=2591/240/63 hdd: 16514064 sectors (8455 MB) w/512KiB Cache, CHS=16383/16/63 hde: 3428036 sectors (1755 MB) w/128KiB Cache, CHS=3400/16/63, DMA Partition check: hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 > hdd: [PTBL] [1027/255/63] hdd1 hde:hde: lost interrupt hde: lost interrupt hde: lost interrupt ide_dmaproc: chipset supported ide_dma_lostirq func only: 13 hde: lost interrupt [PTBL] [850/64/63] hde1 hde2 <ide_dmaproc: chipset supported ide_dma_lostirq fu nc only: 13 hde: lost interrupt hde5ide_dmaproc: chipset supported ide_dma_lostirq func only: 13 hde: lost interrupt . . . #Ele carrega o driver bem depois, como carregar bem no inicio ? Found Controller: HPT372 UDMA/ATA133 RAID Controller scsi1 : hpt37x2 Vendor: Maxtor 8 Model: 1750 A4 Rev: 7A3D Type: Direct-Access ANSI SCSI revision: 02 Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 SCSI device sda: 3428036 512-byte hdwr sectors (1755 MB) sda: sda1 sda2 < sda5 sda6 > On Fri, 25 Apr 2003 16:38:01 -0300 "Douglas A. Augusto" <[EMAIL PROTECTED]> wrote: > Pessoal, > > Tentei rodar o linux com o disco IDE espetado na controladora HPT374 e no > momento do reconhecimento do disco, "kernel panic". > > Que argumento deveria passar ao kernel? > > Compilei o modulo hpt374.o, mas estou pessimista, pois não sei se o módulo > estaria carregado quando, no boot, houvesse a tentativa de detecção do HD. > > Infelizmente nesse caso não é muito interessante ir na base da tentativa, pois > tenho que abrir a máquina para alternar entre controladora IDE e HPT. > > Kernel 2.4.20-1-k7 > HD Seagate ATA100 > > Grato, > > -- > Douglas Augusto > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] -- Att. .''`. Thiago Marangoni Zerbinato - [thiagomz] : :' : [EMAIL PROTECTED] - UIN #75311127 `. `'` http://mod-extreme.kit.net <-- Sítio Pessoal `- GNU/Linux User #286429 - Debian User #534 Visite: irc.debian.org #debian-br #debian-sp