Ola pessoal, Tambem estou com problemas para configurar minha placa de rede. No meu caso, eh uma placa SiS900 onboard na asus p4s8x-x. Ao iniciar e ao tentar configura-la com o etherconf, tenho o seguinte erro:
eth0: ERROR while getting interface flags: No such device Ao dar um ifconfig eth0: eth0: error fetching interface information: Device not found com lspci -v (cortando o que interessa): 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 91) Subsystem: Asustek Computer, Inc.: Unknown device 80a7 Flags: bus master, medium devsel, latency 32, IRQ 3 I/O ports at 9800 [size=256] Memory at dd000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at efee0000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 com dmesg | grep eth0 inicialmente nao retorna nada. Ao usar o kudzu, ele retorna: eth0: Realtek RTL8201 PHY transceiver found at address 1. eth0: Using transceiver found at address 1 as default eth0: SiS 900 PCI Fast Ethernet at 0x9800, IRQ 3, 00:0c:6e:44:09:3b. Mas mesmo assim continua nao funcionando. Obrigado Alexandre Martani Em Sun, 7 Mar 2004 01:30:15 -0300 (BRT) linuser <[EMAIL PROTECTED]> escreveu: > > At 01:08 6/3/2004 -0300, you wrote: > >quando dá lspci aparece somente Realtek 10/100 Mbps Ethernet PHY ? > > Bom, pessoal, apaguei o enorme thread que estava anexo, e recomecei > novamente a mensagem. O que ocorre com o dispositivo de rede é que > não funciona. > Tenho os seguinte dados: > > 1-o dispositivo ethernet é onboard (placa asus a7v8xx) > > 2- um lspci -v resulta no seguinte (cortei coisas que não interessam): > > 00:12.0 Ethernet controller: VIA Technologies, Inc. Ethernet > Controller > (rev 74) > Subsystem: Asustek Computer, Inc.: Unknown device 80a1 > Flags: bus master, stepping, medium devsel, latency 32, IRQ 9 > I/O ports at b000 [size=256] > Memory at f0800000 (32-bit, non-prefetchable) [size=256] > Capabilities: [40] Power Management version 2 > > 3- um ifconfig -a resulta no seguinte: > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:36 errors:0 dropped:0 overruns:0 frame:0 > TX packets:36 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:2363 (2.3 KiB) TX bytes:2363 (2.3 KiB) > > 4- o arquivo de configuração do kernel (.config) contém, na seção > correspondente a dispositivo ethernet, o seguinte: > > ***** INICIO DO .config ******** > # > # Ethernet (10 or 100Mbit) > # > CONFIG_NET_ETHERNET=y > # CONFIG_SUNLANCE is not set > CONFIG_HAPPYMEAL=m > # CONFIG_SUNBMAC is not set > # CONFIG_SUNQE is not set > CONFIG_SUNGEM=m > CONFIG_NET_VENDOR_3COM=y > CONFIG_EL1=m > CONFIG_EL2=m > CONFIG_ELPLUS=m > CONFIG_EL16=m > CONFIG_EL3=m > CONFIG_3C515=m > # CONFIG_ELMC is not set > # CONFIG_ELMC_II is not set > CONFIG_VORTEX=m > CONFIG_LANCE=m > CONFIG_NET_VENDOR_SMC=y > CONFIG_WD80x3=m > # CONFIG_ULTRAMCA is not set > CONFIG_ULTRA=m > # CONFIG_ULTRA32 is not set > CONFIG_SMC9194=m > CONFIG_NET_VENDOR_RACAL=y > CONFIG_NI5010=m > CONFIG_NI52=m > CONFIG_NI65=m > CONFIG_AT1700=m > CONFIG_DEPCA=m > CONFIG_HP100=m > CONFIG_NET_ISA=y > CONFIG_E2100=m > CONFIG_EWRK3=m > CONFIG_EEXPRESS=m > CONFIG_EEXPRESS_PRO=m > CONFIG_HPLAN_PLUS=m > CONFIG_HPLAN=m > CONFIG_LP486E=m > CONFIG_ETH16I=m > CONFIG_NE2000=m > CONFIG_NET_PCI=y > CONFIG_PCNET32=y > CONFIG_ADAPTEC_STARFIRE=m > CONFIG_AC3200=m > CONFIG_APRICOT=m > CONFIG_CS89x0=m > CONFIG_TULIP=m > # CONFIG_TULIP_MWI is not set > # CONFIG_TULIP_MMIO is not set > CONFIG_DE4X5=m > CONFIG_DGRS=m > CONFIG_DM9102=m > CONFIG_EEPRO100=m > # CONFIG_LNE390 is not set > CONFIG_FEALNX=y > CONFIG_NATSEMI=m > # CONFIG_NATSEMI_CABLE_MAGIC is not set > CONFIG_NE2K_PCI=y > # CONFIG_NE3210 is not set > # CONFIG_ES3210 is not set > CONFIG_8139CP=y > CONFIG_8139TOO=y > # CONFIG_8139TOO_PIO is not set > # CONFIG_8139TOO_TUNE_TWISTER is not set > CONFIG_8139TOO_8129=y > # CONFIG_8139_NEW_RX_RESET is not set > CONFIG_SIS900=y > CONFIG_EPIC100=m > CONFIG_SUNDANCE=m > CONFIG_TLAN=m > CONFIG_VIA_RHINE=m > # CONFIG_VIA_RHINE_MMIO is not set > CONFIG_WINBOND_840=y > CONFIG_NET_POCKET=y > CONFIG_ATP=m > CONFIG_DE600=m > CONFIG_DE620=m > > ****** FIM DO .config ********* > > Alguém sabe qual a solução? > > Abraços. > Paulo > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > -- Alexandre Martani amartani em uol com br Ainda usando Rwindow$ + Internet Exploder + Outloco Expresso? Mude! GNU/Linux + Mozilla Firefox + Sylpheed