Do you have scsi cd support? also to make scd's do ./MAKEDEV scd## where ## is a number.
Make those, keep out ide-cdrom support, keep in ide-scsi emultaion, keep in scsi cd, scsi generic. try it and LMK --dave On 10 Sep 1999, Morgan Fletcher wrote: > David Blackman <[EMAIL PROTECTED]> writes: > > Okay, listen here's the deal: you need to take OUT ide-cd support > > Done. > > > leave in scsi-emulation, scsi-generic, scsi-cdrom...... > > now ./MAKDEV sg > > Done. I now have /dev/sg[0-16]. > > > I'm pretty sure that the /dev/scd* come pre-made > > the important thing is to see if you get messages like this on bootup: > > scsi0 : AdvanSys SCSI 3.1E: PCI 20 CDB: IO E400/F, IRQ 9 > > scsi1 : SCSI host adapter emulation for IDE ATAPI devices > > scsi : 2 hosts. > > Vendor: HP Model: C5110A Rev: 3638 > > Type: Processor ANSI SCSI revision: 02 > > Detected scsi generic sga at scsi0, channel 0, id 1, lun 0 > > Vendor: IOMEGA Model: ZIP 100 Rev: 13.A > > Type: Direct-Access ANSI SCSI revision: 00 > > Detected scsi removable disk sda at scsi1, channel 0, id 0, lun 0 > > Vendor: E-IDE Model: CD-ROM 45X/A Rev: 30 > > Type: CD-ROM ANSI SCSI revision: 02 > > Detected scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0 > > Vendor: PHILIPS Model: CDD3610 CD-R/RW Rev: 3.08 > > Type: CD-ROM ANSI SCSI revision: 02 > > Detected scsi CD-ROM sr1 at scsi1, channel 0, id 2, lun 0 > > scsi : detected 2 SCSI cdroms 1 SCSI disk total. > > sr0: scsi3-mmc drive: 0x/20x xa/form2 cdda tray > > Uniform CDROM driver Revision: 2.55 > > sr1: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray > > SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB] > > I don't. Rather, I see: > > (scsi0) <Adaptec AHA-294X SCSI host adapter> found at PCI 14/0 > (scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs > (scsi0) Warning - detected auto-termination > (scsi0) Please verify driver detected settings are correct. > (scsi0) If not, then please properly set the device termination > (scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted > (scsi0) during machine bootup. > (scsi0) Cables present (Int-50 YES, Ext-50 NO) > (scsi0) Downloading sequencer code... 406 instructions downloaded > scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.17/3.2.4 > <Adaptec AHA-294X SCSI host adapter> > scsi : 1 host. > (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15. > Vendor: SEAGATE Model: ST34371N Rev: 0338 > Type: Direct-Access ANSI SCSI revision: 02 > Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 > (scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15. > Vendor: MATSHITA Model: CD-ROM CR-506 Rev: 8S05 > Type: CD-ROM ANSI SCSI revision: 02 > scsi : detected 1 SCSI disk total. > SCSI device sda: hdwr sector= 512 bytes. Sectors= 8496960 [4148 MB] [4.1 GB] > > I guess I need to put something that's currently a module back in the > kernel, maybe ide-scsi? Is it built into your kernel? Would you mind > sending me your kernel .config? And what kernel rev are you running? > > Thanks for the reply. > > > this means for cdrecord I do dev=1,2,0 > > morgan > -- > VVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVV > >> M o r g a n F l e t c h e r http://www.hahaha.org << > >> Tibi gratias agimus quod nihil fumas. [EMAIL PROTECTED] << > > > -- > Unsubscribe? mail -s unsubscribe [EMAIL PROTECTED] < /dev/null > > >

