You DON'T have scsi emulation in there. make sure scsi-emulation is on, scsi cdrom si on, ide cdrom is off. make sure you installed the kernel (I know taht sounds stupid, but hey, my first kernels sat there in arch/i386/boot)
if you had scsi-emu workign you'd have 2 scsi hosts LMK --dave On 10 Sep 1999, Morgan Fletcher wrote: > David Blackman <[EMAIL PROTECTED]> writes: > > Okay, listen here's the deal: you need to take OUT ide-cd support > > Done. > > > leave in scsi-emulation, scsi-generic, scsi-cdrom...... > > now ./MAKDEV sg > > Done. I now have /dev/sg[0-16]. > > > I'm pretty sure that the /dev/scd* come pre-made > > the important thing is to see if you get messages like this on bootup: > > scsi0 : AdvanSys SCSI 3.1E: PCI 20 CDB: IO E400/F, IRQ 9 > > scsi1 : SCSI host adapter emulation for IDE ATAPI devices > > scsi : 2 hosts. > > Vendor: HP Model: C5110A Rev: 3638 > > Type: Processor ANSI SCSI revision: 02 > > Detected scsi generic sga at scsi0, channel 0, id 1, lun 0 > > Vendor: IOMEGA Model: ZIP 100 Rev: 13.A > > Type: Direct-Access ANSI SCSI revision: 00 > > Detected scsi removable disk sda at scsi1, channel 0, id 0, lun 0 > > Vendor: E-IDE Model: CD-ROM 45X/A Rev: 30 > > Type: CD-ROM ANSI SCSI revision: 02 > > Detected scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0 > > Vendor: PHILIPS Model: CDD3610 CD-R/RW Rev: 3.08 > > Type: CD-ROM ANSI SCSI revision: 02 > > Detected scsi CD-ROM sr1 at scsi1, channel 0, id 2, lun 0 > > scsi : detected 2 SCSI cdroms 1 SCSI disk total. > > sr0: scsi3-mmc drive: 0x/20x xa/form2 cdda tray > > Uniform CDROM driver Revision: 2.55 > > sr1: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray > > SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB] > > I don't. Rather, I see: > > (scsi0) <Adaptec AHA-294X SCSI host adapter> found at PCI 14/0 > (scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs > (scsi0) Warning - detected auto-termination > (scsi0) Please verify driver detected settings are correct. > (scsi0) If not, then please properly set the device termination > (scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted > (scsi0) during machine bootup. > (scsi0) Cables present (Int-50 YES, Ext-50 NO) > (scsi0) Downloading sequencer code... 406 instructions downloaded > scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.17/3.2.4 > <Adaptec AHA-294X SCSI host adapter> > scsi : 1 host. > (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15. > Vendor: SEAGATE Model: ST34371N Rev: 0338 > Type: Direct-Access ANSI SCSI revision: 02 > Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 > (scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15. > Vendor: MATSHITA Model: CD-ROM CR-506 Rev: 8S05 > Type: CD-ROM ANSI SCSI revision: 02 > scsi : detected 1 SCSI disk total. > SCSI device sda: hdwr sector= 512 bytes. Sectors= 8496960 [4148 MB] [4.1 GB] > > I guess I need to put something that's currently a module back in the > kernel, maybe ide-scsi? Is it built into your kernel? Would you mind > sending me your kernel .config? And what kernel rev are you running? > > Thanks for the reply. > > > this means for cdrecord I do dev=1,2,0 > > morgan > -- > VVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVV > >> M o r g a n F l e t c h e r http://www.hahaha.org << > >> Tibi gratias agimus quod nihil fumas. [EMAIL PROTECTED] << > >