hi ya nate... i've seen that silly "card reports noRX buffer" errors...
i usually just rerun lilo and it seems to clear it up on my D815EEAAL mb w/ onboard nic.. and if i have other pci-based nics...i still go those RX buffer problems...so its just "timing" ?? somewhere on the mb or bios or network driver...but since tulip drivers and eepro is different... think its the mb itself or disk latency ???? c ya alvin On Sun, 3 Sep 2000, Nate Duehr wrote: > Hi Nate! :) > > If it's any help for anyone smarter than I, I've seen this same problem > on a Dell GX100 with on-board EEPRO100 card and the Intel810i chipset > (which I know requires much joy and the agpart module loaded to get X > working) at the office... > > A complete hardware restart usually clears it? > > On Wed, Aug 30, 2000 at 01:28:41PM -0700, Nate Amsden wrote: > > This started happening recently. Sometimes when i boot up my screen > > floods with : > > > > eth0: card reports no RX buffers. > > eth0: card reports no resources. > > eth0: card reports no RX buffers. > > > > over and over again.. at first i thought it was an IRQ conflict but > > nothing in the system had changed it just started out of nowhere > > apparently(after a reboot once) i figured a way around it, to > > /etc/init.d/networking stop then start it again after a few > > seconds(haven't tried to issue just a restart) and the errors stop. was > > wondering if this could be the result of the system booting too fast ? > > my system takes about 6 seconds from when init loads to when X > > launches(probably more like 4-5 seconds) the same hardware when i was > > running slower stuff(128MB as opposed to 512MB and 466mhz as opposed to > > 800mhz) this never happened. Running on an Asus CUV4X(VIA Apollo > > Pro133A). I did move the NIC from PCI#4 to PCI#2 with no difference. > > > > really odd. > > > > Running debian 2.2r0 linux 2.2.17pre18 > > > > > > > > eth0: Intel PCI EtherExpress Pro100 82557, 00:90:27:9B:16:D6, I/O at > > 0xa800, IRQ 10. > > Receiver lock-up bug exists -- enabling work-around. > > Board assembly 721383-006, Physical connectors present: RJ45 > > Primary interface chip i82555 PHY #1. > > General self-test: passed. > > Serial sub-system self-test: passed. > > Internal registers self-test: passed. > > ROM checksum self-test: passed (0x04f4518b). > > eepro100.c:v1.09j-t 9/29/99 Donald Becker > > http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html > > eepro100.c: $Revision: 1.20.2.10 $ 2000/05/31 Modified by Andrey V. > > Savochkin <[EMAIL PROTECTED]> and others > > > > > > more info: > > > > [EMAIL PROTECTED]:~$ cat /proc/interrupts > > CPU0 > > 0: 47060 XT-PIC timer > > 1: 2469 XT-PIC keyboard > > 2: 0 XT-PIC cascade > > 8: 1 XT-PIC rtc > > 10: 797 XT-PIC eth0 > > 11: 0 XT-PIC es1370 > > 12: 17762 XT-PIC PS/2 Mouse > > 13: 1 XT-PIC fpu > > 14: 0 XT-PIC usb-uhci, usb-uhci > > 15: 26279 XT-PIC aic7xxx > > [EMAIL PROTECTED]:~$ cat /proc/ioports > > 0000-001f : dma1 > > 0020-003f : pic1 > > 0040-005f : timer > > 0060-006f : keyboard > > 0070-007f : rtc > > 0080-008f : dma page reg > > 00a0-00bf : pic2 > > 00c0-00df : dma2 > > 00f0-00ff : fpu > > 02e8-02ef : serial(set) > > 02f8-02ff : serial(set) > > 0378-037f : parport0 > > 03c0-03df : vga+ > > 03f8-03ff : serial(set) > > 0778-077a : parport0 > > a000-a03f : es1370 > > a400-a4fe : aic7xxx > > a800-a81f : Intel Speedo3 Ethernet > > b000-b013 : usb-uhci > > b400-b413 : usb-uhci > > e800-e807 : via2-smbus > > > > > > > > any idea ? thanks for any input! > > > > nate > > > > -- > > ::: > > ICQ: 75132336 > > http://www.aphroland.org/ > > http://www.linuxpowered.net/ > > [EMAIL PROTECTED] > > > > > > -- > > Unsubscribe? mail -s unsubscribe [EMAIL PROTECTED] < /dev/null > > > > -- > Nate Duehr <[EMAIL PROTECTED]> > > GPG Key fingerprint = DCAF 2B9D CC9B 96FA 7A6D AAF4 2D61 77C5 7ECE C1D2 > Public Key available upon request, or at wwwkeys.pgp.net and others. >