Hello Guys, I'm trying to erase and burn my cd-rw. I'm sure that there is no problem with my cd-rw media as it works on my other system. After unsuccessful attempt to burn it with k3b I have gone to command line to see what is going on. For command line I have followed steps described here: http://www.linuxconfig.org/Create_and_burn_ISO_images_with_mkisofs_%26_cdrecord
Here is a output, everything looks fine but last 6 lines. Help is much appreciated. Thank you OUTPUT: wodim: No write mode specified. wodim: Asuming -tao mode. wodim: Future versions of wodim may have different drive dependent defaults. TOC Type: 1 = CD-ROM scsidev: '/dev/hdc' devname: '/dev/hdc' scsibus: -2 target: -2 lun: -2 Linux sg driver version: 3.5.27 Wodim version: 1.1.2 SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'COMPAL ' Identification : 'TSD80Y1 DVD RW ' Revision : 'D010' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: 0x000A (CD-RW) Profile: 0x001B (DVD+R) Profile: 0x001A (DVD+RW) Profile: 0x0014 (DVD-RW sequential recording) Profile: 0x0013 (DVD-RW restricted overwrite) Profile: 0x0011 (DVD-R sequential recording) Profile: 0x0010 (DVD-ROM) Profile: 0x000A (CD-RW) (current) Profile: 0x0009 (CD-R) Profile: 0x0008 (CD-ROM) Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1638400 = 1600 KB Beginning DMA speed test. Set CDR_NODMATEST environment variable if device communication breaks or freezes immediately after that. Drive DMA Speed: 4449 kB/s 25x CD 3x DVD FIFO size : 12582912 = 12288 KB Track 01: data 556 MB Total size: 639 MB (63:21.21) = 285091 sectors Lout start: 639 MB (63:23/16) = 285091 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 2 Reference speed: 6 Is not unrestricted Is erasable Disk sub type: High speed Rewritable (CAV) media (1) ATIP start of lead in: -11077 (97:34/23) ATIP start of lead out: 359849 (79:59/74) 1T speed low: 4 1T speed high: 10 2T speed low: 2 2T speed high: 10 power mult factor: 2 6 recommended erase/write power: 5 A1 values: 24 2C DC A2 values: 14 A4 4A A3 values: 04 C4 80 Disk type: Phase change Manuf. index: 11 Manufacturer: Mitsubishi Chemical Corporation Blocks total: 359849 Blocks current: 359849 Blocks remaining: 74758 Speed set to 2116 KB/s Starting to write CD/DVD at speed 12.0 in real TAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. Performing OPC... Errno: 0 (Success), send opc scsi sendcmd: no error CDB: 54 01 00 00 00 00 00 00 00 00 status: 0x4 (CONDITION MET/GOOD) cmd finished after 60.053s timeout 60s wodim: OPC failed. Writing time: 174.939s -- lubo http://www.linuxconfig.org/ -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
