On 8/12/23 15:27, Greg Wooledge wrote:
On Sat, Aug 12, 2023 at 02:49:25PM -0400, gene heskett wrote:
I am bringing up a new bananapi-m5, an arm64 device. You don't like my way,
and have made that boringly plain.
Gene. Please stop saying things like this. The use of traditional static
addressing without DNS is a common and well-supported configuration.
People do it ALL THE TIME. It's extremely simple.
Already edited the /etc/hostname
Good. This is where your hostname goes. Your hostname can either be
"short" (no dots), or "long" (with dots).
and /etc/hosts files.
Also good. Your hostname should resolve either to your static IP
address, or to 127.0.1.1. Either way is fine.
ipv6:
There is no ipv6 service within 100 miles, so I should set a /proc command
to kill ipv6, so whats the official syntax? for that.
Do nothing. Do not touch anything with "ipv6" in its name at all.
ipv4:
Step one: determine the NAME of your ethernet interface.
eth0
Step two: edit /etc/network/interfaces to bring up this interface with
your desired IP address, netmask, and gateway. If there's a running
DHCP client daemon (because the installer set it up for DHCP instead
of static addressing), you may need to kill that daemon. Or, if you're
especially clever, you can bring the interface DOWN, BEFORE editing
the file, which will kill the daemon cleanly. Most people forget this
step, so they just end up killing the daemon later, with "kill" or
by rebooting.
interface had lo already
added
iface eth0 inet static
address 192.168.71.55
gateway 192.168.71.2
correct? editor saved to do resolv.conf next
That daemons name?
Step three: edit /etc/resolv.conf to set up DNS resolution for outside
hosts, if you intend to use the Internet.
Here's a sample /etc/network/interfaces file:
====================================================
source /etc/network/interfaces.d/*
auto lo
iface lo inet loopback
auto enp2s0
iface enp2s0 inet static
address 10.0.0.7/24
gateway 10.0.0.1
====================================================
Here's a sample /etc/resolv.conf file:
====================================================
search coyote.den
nameserver 1.1.1.1
I use my router @192.168.71.1 as a nameserver relay
saved that, restarted /etc/init.d/networking. got good ipv4 address for
ip a but no route by ip r.
next?
====================================================
Of course, if you're running a local recursive DNS nameserver, you would
put "nameserver 127.0.0.1". Or you might use your ISP's nameserver, or
a recursive nameserver elsewhere on your network. Use whatever's correct
for your setup.
Finally, here's a sample /etc/hosts file:
eth0
====================================================
127.0.0.1 localhost
::1 localhost ip6-localhost ip6-loopback
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
10.0.0.7 banana1.coyote.den banana1
10.0.0.8 printer.coyote.den printer
10.0.0.19 raspberry1.coyote.den raspberry1
====================================================
Make sure the output of "hostname", which should match the contents of
your /etc/hostname file, matches one of the lines in this file.
And that's the entire thing! Do not touch anything else.
It all matches, but no route for ip r.
.
Cheers, Gene Heskett.
--
"There are four boxes to be used in defense of liberty:
soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author, 1940)
If we desire respect for the law, we must first make the law respectable.
- Louis D. Brandeis
Genes Web page <http://geneslinuxbox.net:6309/>
