Salut à tous!!!!!
J'ai un problème pour graver avec xcdroast. J'ai installé la Mandrake 8.2 puis, comme j'ai un graveur IDE, j'ai fait une émulation SCSI de la façon suivante : ajout de append="hdb=ide-scsi" dans /etc/lilo.conf puis j'ai tapé sous la console /sbin/lilo -v puis modprobe ide-scsi puis reboot. Pour avoir les messages de boot je lance dmesg, et visiblement mon graveur est bien émulé en scsi. Adding Swap: 248968k swap-space (priority -1) SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices --------------------------------------------------------- Vendor: MITSUMI Model: CR-4804TE Rev: 2.4C Type: CD-ROM ANSI SCSI revision: 02 kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,6), internal journal EXT3-fs: mounted filesystem with ordered data mode. parport0: PC-style at 0x378 [PCSPP,EPP] IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. es1371: version v0.30 time 03:23:01 Mar 15 2002 PCI: Found IRQ 10 for device 00:0d.0 es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x08 es1371: found es1371 rev 8 at io 0xb800 irq 10 es1371: features: joystick 0x0 PCI: Setting latency timer of device 00:0d.0 to 64 ac97_codec: AC97 Audio codec, id: 0x4352:0x5913 (Cirrus Logic CS4297A rev A) Splash status on console 0 changed to off Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 --------------------------------------------------------- sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 Pour vérifier, je lance la commande mount et on voit que le graveur de cdrom est connu comme /dev/scd0 et plus comme /dev/hdb : [root@localhost yukio]# mount /dev/hda1 on / type ext3 (rw) none on /proc type proc (rw) none on /dev type devfs (rw) none on /dev/pts type devpts (rw,mode=0620) none on /dev/shm type tmpfs (rw) /dev/hda6 on /home type ext3 (rw) /mnt/cdrom on /mnt/cdrom type supermount (ro,dev=/dev/scd0,fs=iso9660,--,iocharset=iso8859-15) ----------------------------------------------------------------------------------------------/mnt/floppy on /mnt/floppy typee supermount (rw,sync,dev=/dev/fd0,fs=vfat,--,iocharset=iso8859-15,umask=0,codepage=850) [root@localhost yukio]# Quand je lance xcdroast sous root j'ai des warnings mais dans l'écran de configuration j'ai bien mon graveur de reconnu : [root@localhost yukio]# xcdroast & [2] 2223 [1] Done xcdroast [root@localhost yukio]# ** WARNING **: Installation problem? No set-uid bit on /usr/bin/mkisofs ** WARNING **: Installation problem? No set-uid bit on /usr/bin/readcd ** WARNING **: Installation problem? No set-uid bit on /usr/bin/cdda2wav [root@localhost yukio]# Quand je veux graver une image ISO ( obtenue sous xcdroast avec l'option Mastérisation de l'image ) j'ai les messages suivants sous xcdroast. Est-ce que scsidev: '0,0,0' signifie qu'il y a pas de graveur scsi reconnu? Le mode choisi dans l'onglet Ecrire Pistes Track at Once ( TAO ), et le bouton que je clique est "Fixer uniquement CD-R-RW ) plutôt que Ecrire les pistes qui ne marche pas. scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.22 Cdrecord 1.11a15 (i586-mandrake-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling TOC Type: 1 = CD-ROM Using libscg version 'schily-0.5' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 1 Vendor_info : 'MITSUMI ' Identifikation : 'CR-4804TE ' Revision : '2.4C' Device seems to be: Philips CDD-522. Using generic SCSI-3/mmc CD-R driver (mmc_cdr). Driver flags : SWABAUDIO Supported modes: TAO PACKET RAW/R16 RAW/R96R Drive buf size : 1343488 = 1312 KB Current Secsize: 2048 ATIP info from disk: Indicated writing power: 4 Is not unrestricted Is not erasable ATIP start of lead in: -11660 (97:26/40) ATIP start of lead out: 336225 (74:45/00) Disk type: Long strategy type (Cyanine, AZO or similar) Manuf. index: 6 Manufacturer: FUJI Photo Film Co., Ltd. Blocks total: 336225 Blocks current: 336225 Blocks remaining: 336375 RBlocks total: 346210 RBlocks current: 346210 RBlocks remaining: 346360 Starting to write CD/DVD at speed 4 in write mode for single session. 0 seconds. Operation starts. Performing OPC... Writing time: 1.196s Fixating... Fixating time: 0.004s J'ai un message dans une fenêtre disant que tous s'est bien passé mais on grave pas 300 mégas en 0 secondes :-)) Après je fais [yukio@localhost tmp]$ ls /mnt/cdrom/ ls: /mnt/cdrom/: Erreur d'entrée/sortie bref ça marche pas mais je dois pas en être loin :-))
Vous souhaitez acquerir votre Pack ou des Services MandrakeSoft? Rendez-vous sur "http://www.mandrakestore.com"