On 2015-02-25 07:14, Ouyang, Changchun wrote:
>
>
>> -----Original Message-----
>> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Pawel Wodkowski
>> Sent: Thursday, February 19, 2015 11:55 PM
>> To: dev at dpdk.org
>> Subject: [dpdk-dev] [PATCH v4 4/7] move rte_eth_dev_check_mq_mode()
>> logic to driver
>>
>> Function rte_eth_dev_check_mq_mode() is driver specific. It should be
>> done in PF configuration phase. This patch move igb/ixgbe driver specific mq
>> check and SRIOV configuration code to driver part. Also rewriting log
>> messages to be shorter and more descriptive.
>>
>> Signed-off-by: Pawel Wodkowski <pawelx.wodkowski at intel.com>
>> ---
>> lib/librte_ether/rte_ethdev.c | 197
>> -----------------------------------
>> lib/librte_pmd_e1000/igb_ethdev.c | 43 ++++++++
>> lib/librte_pmd_ixgbe/ixgbe_ethdev.c | 105 ++++++++++++++++++-
>> lib/librte_pmd_ixgbe/ixgbe_ethdev.h | 5 +-
>> lib/librte_pmd_ixgbe/ixgbe_pf.c | 202
>> +++++++++++++++++++++++++++++++-----
>> 5 files changed, 327 insertions(+), 225 deletions(-)
>>
>> diff --git a/lib/librte_ether/rte_ethdev.c b/lib/librte_ether/rte_ethdev.c
>> index 4007054..aa27e39 100644
>> --- a/lib/librte_ether/rte_ethdev.c
>> +++ b/lib/librte_ether/rte_ethdev.c
>> @@ -502,195 +502,6 @@ rte_eth_dev_tx_queue_config(struct rte_eth_dev
>> *dev, uint16_t nb_queues)
>> return (0);
>> }
>>
>> -static int
>> -rte_eth_dev_check_vf_rss_rxq_num(uint8_t port_id, uint16_t nb_rx_q) -{
>> - struct rte_eth_dev *dev = &rte_eth_devices[port_id];
>> - switch (nb_rx_q) {
>> - case 1:
>> - case 2:
>> - RTE_ETH_DEV_SRIOV(dev).active =
>> - ETH_64_POOLS;
>> - break;
>> - case 4:
>> - RTE_ETH_DEV_SRIOV(dev).active =
>> - ETH_32_POOLS;
>> - break;
>> - default:
>> - return -EINVAL;
>> - }
>> -
>> - RTE_ETH_DEV_SRIOV(dev).nb_rx_q_per_pool = nb_rx_q;
>> - RTE_ETH_DEV_SRIOV(dev).def_pool_q_idx =
>> - dev->pci_dev->max_vfs * nb_rx_q;
>> -
>> - return 0;
>> -}
>> -
>> -static int
>> -rte_eth_dev_check_mq_mode(uint8_t port_id, uint16_t nb_rx_q, uint16_t
>> nb_tx_q,
>> - const struct rte_eth_conf *dev_conf)
>> -{
>> - struct rte_eth_dev *dev = &rte_eth_devices[port_id];
>> -
>> - if (RTE_ETH_DEV_SRIOV(dev).active != 0) {
>> - /* check multi-queue mode */
>> - if ((dev_conf->rxmode.mq_mode == ETH_MQ_RX_DCB) ||
>> - (dev_conf->rxmode.mq_mode == ETH_MQ_RX_DCB_RSS)
>> ||
>> - (dev_conf->txmode.mq_mode == ETH_MQ_TX_DCB)) {
>> - /* SRIOV only works in VMDq enable mode */
>> - PMD_DEBUG_TRACE("ethdev port_id=%" PRIu8
>> - " SRIOV active, "
>> - "wrong VMDQ mq_mode rx %u
>> tx %u\n",
>> - port_id,
>> - dev_conf->rxmode.mq_mode,
>> - dev_conf->txmode.mq_mode);
>> - return (-EINVAL);
>> - }
>> -
>> - switch (dev_conf->rxmode.mq_mode) {
>> - case ETH_MQ_RX_VMDQ_DCB:
>> - case ETH_MQ_RX_VMDQ_DCB_RSS:
>> - /* DCB/RSS VMDQ in SRIOV mode, not implement
>> yet */
>> - PMD_DEBUG_TRACE("ethdev port_id=%" PRIu8
>> - " SRIOV active, "
>> - "unsupported VMDQ mq_mode
>> rx %u\n",
>> - port_id, dev_conf-
>>> rxmode.mq_mode);
>> - return (-EINVAL);
>> - case ETH_MQ_RX_RSS:
>> - PMD_DEBUG_TRACE("ethdev port_id=%" PRIu8
>> - " SRIOV active, "
>> - "Rx mq mode is changed from:"
>> - "mq_mode %u into VMDQ
>> mq_mode %u\n",
>> - port_id,
>> - dev_conf->rxmode.mq_mode,
>> - dev->data-
>>> dev_conf.rxmode.mq_mode);
>> - case ETH_MQ_RX_VMDQ_RSS:
>> - dev->data->dev_conf.rxmode.mq_mode =
>> ETH_MQ_RX_VMDQ_RSS;
>> - if (nb_rx_q <=
>> RTE_ETH_DEV_SRIOV(dev).nb_rx_q_per_pool)
>> - if
>> (rte_eth_dev_check_vf_rss_rxq_num(port_id, nb_rx_q) != 0) {
>> - PMD_DEBUG_TRACE("ethdev
>> port_id=%d"
>> - " SRIOV active, invalid queue"
>> - " number for VMDQ RSS,
>> allowed"
>> - " value are 1, 2 or 4\n",
>> - port_id);
>> - return -EINVAL;
>> - }
>> - break;
>> - default: /* ETH_MQ_RX_VMDQ_ONLY or
>> ETH_MQ_RX_NONE */
>> - /* if nothing mq mode configure, use default scheme
>> */
>> - dev->data->dev_conf.rxmode.mq_mode =
>> ETH_MQ_RX_VMDQ_ONLY;
>> - if (RTE_ETH_DEV_SRIOV(dev).nb_rx_q_per_pool > 1)
>> -
>> RTE_ETH_DEV_SRIOV(dev).nb_rx_q_per_pool = 1;
>> - break;
>> - }
>> -
>> - switch (dev_conf->txmode.mq_mode) {
>> - case ETH_MQ_TX_VMDQ_DCB:
>> - /* DCB VMDQ in SRIOV mode, not implement yet */
>> - PMD_DEBUG_TRACE("ethdev port_id=%" PRIu8
>> - " SRIOV active, "
>> - "unsupported VMDQ mq_mode
>> tx %u\n",
>> - port_id, dev_conf-
>>> txmode.mq_mode);
>> - return (-EINVAL);
>> - default: /* ETH_MQ_TX_VMDQ_ONLY or
>> ETH_MQ_TX_NONE */
>> - /* if nothing mq mode configure, use default scheme
>> */
>> - dev->data->dev_conf.txmode.mq_mode =
>> ETH_MQ_TX_VMDQ_ONLY;
>> - break;
>> - }
>> -
>> - /* check valid queue number */
>> - if ((nb_rx_q > RTE_ETH_DEV_SRIOV(dev).nb_tx_q_per_pool)
>> ||
>> - (nb_tx_q > RTE_ETH_DEV_SRIOV(dev).nb_tx_q_per_pool))
>> {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d SRIOV
>> active, "
>> - "queue number must less equal to %d\n",
>> - port_id,
>> RTE_ETH_DEV_SRIOV(dev).nb_q_per_pool);
>> - return (-EINVAL);
>> - }
>> - } else {
>> - /* For vmdb+dcb mode check our configuration before we
>> go further */
>> - if (dev_conf->rxmode.mq_mode ==
>> ETH_MQ_RX_VMDQ_DCB) {
>> - const struct rte_eth_vmdq_dcb_conf *conf;
>> -
>> - if (nb_rx_q != ETH_VMDQ_DCB_NUM_QUEUES) {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d
>> VMDQ+DCB, nb_rx_q "
>> - "!= %d\n",
>> - port_id,
>> ETH_VMDQ_DCB_NUM_QUEUES);
>> - return (-EINVAL);
>> - }
>> - conf = &(dev_conf->rx_adv_conf.vmdq_dcb_conf);
>> - if (! (conf->nb_queue_pools == ETH_16_POOLS ||
>> - conf->nb_queue_pools == ETH_32_POOLS)) {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d
>> VMDQ+DCB selected, "
>> - "nb_queue_pools must
>> be %d or %d\n",
>> - port_id, ETH_16_POOLS,
>> ETH_32_POOLS);
>> - return (-EINVAL);
>> - }
>> - }
>> - if (dev_conf->txmode.mq_mode ==
>> ETH_MQ_TX_VMDQ_DCB) {
>> - const struct rte_eth_vmdq_dcb_tx_conf *conf;
>> -
>> - if (nb_tx_q != ETH_VMDQ_DCB_NUM_QUEUES) {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d
>> VMDQ+DCB, nb_tx_q "
>> - "!= %d\n",
>> - port_id,
>> ETH_VMDQ_DCB_NUM_QUEUES);
>> - return (-EINVAL);
>> - }
>> - conf = &(dev_conf-
>>> tx_adv_conf.vmdq_dcb_tx_conf);
>> - if (! (conf->nb_queue_pools == ETH_16_POOLS ||
>> - conf->nb_queue_pools == ETH_32_POOLS)) {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d
>> VMDQ+DCB selected, "
>> - "nb_queue_pools != %d or
>> nb_queue_pools "
>> - "!= %d\n",
>> - port_id, ETH_16_POOLS,
>> ETH_32_POOLS);
>> - return (-EINVAL);
>> - }
>> - }
>> -
>> - /* For DCB mode check our configuration before we go
>> further */
>> - if (dev_conf->rxmode.mq_mode == ETH_MQ_RX_DCB) {
>> - const struct rte_eth_dcb_rx_conf *conf;
>> -
>> - if (nb_rx_q != ETH_DCB_NUM_QUEUES) {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d
>> DCB, nb_rx_q "
>> - "!= %d\n",
>> - port_id,
>> ETH_DCB_NUM_QUEUES);
>> - return (-EINVAL);
>> - }
>> - conf = &(dev_conf->rx_adv_conf.dcb_rx_conf);
>> - if (! (conf->nb_tcs == ETH_4_TCS ||
>> - conf->nb_tcs == ETH_8_TCS)) {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d
>> DCB selected, "
>> - "nb_tcs != %d or nb_tcs "
>> - "!= %d\n",
>> - port_id, ETH_4_TCS,
>> ETH_8_TCS);
>> - return (-EINVAL);
>> - }
>> - }
>> -
>> - if (dev_conf->txmode.mq_mode == ETH_MQ_TX_DCB) {
>> - const struct rte_eth_dcb_tx_conf *conf;
>> -
>> - if (nb_tx_q != ETH_DCB_NUM_QUEUES) {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d
>> DCB, nb_tx_q "
>> - "!= %d\n",
>> - port_id,
>> ETH_DCB_NUM_QUEUES);
>> - return (-EINVAL);
>> - }
>> - conf = &(dev_conf->tx_adv_conf.dcb_tx_conf);
>> - if (! (conf->nb_tcs == ETH_4_TCS ||
>> - conf->nb_tcs == ETH_8_TCS)) {
>> - PMD_DEBUG_TRACE("ethdev port_id=%d
>> DCB selected, "
>> - "nb_tcs != %d or nb_tcs "
>> - "!= %d\n",
>> - port_id, ETH_4_TCS,
>> ETH_8_TCS);
>> - return (-EINVAL);
>> - }
>> - }
>> - }
>> - return 0;
>> -}
>> -
>> int
>> rte_eth_dev_configure(uint8_t port_id, uint16_t nb_rx_q, uint16_t nb_tx_q,
>> const struct rte_eth_conf *dev_conf) @@ -798,14 +609,6
>> @@ rte_eth_dev_configure(uint8_t port_id, uint16_t nb_rx_q, uint16_t
>> nb_tx_q,
>> ETHER_MAX_LEN;
>> }
>>
>> - /* multipe queue mode checking */
>> - diag = rte_eth_dev_check_mq_mode(port_id, nb_rx_q, nb_tx_q,
>> dev_conf);
>> - if (diag != 0) {
>> - PMD_DEBUG_TRACE("port%d
>> rte_eth_dev_check_mq_mode = %d\n",
>> - port_id, diag);
>> - return diag;
>> - }
>> -
>> /*
>> * Setup new number of RX/TX queues and reconfigure device.
>> */
>> diff --git a/lib/librte_pmd_e1000/igb_ethdev.c
>> b/lib/librte_pmd_e1000/igb_ethdev.c
>> index d451086..5c922df 100644
>> --- a/lib/librte_pmd_e1000/igb_ethdev.c
>> +++ b/lib/librte_pmd_e1000/igb_ethdev.c
>> @@ -742,6 +742,49 @@ eth_igb_configure(struct rte_eth_dev *dev)
>> struct e1000_interrupt *intr =
>> E1000_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
>>
>> + enum rte_eth_rx_mq_mode rx_mq_mode = dev->data-
>>> dev_conf.rxmode.mq_mode;
>> + enum rte_eth_tx_mq_mode tx_mq_mode =
>> +dev->data->dev_conf.txmode.mq_mode;
>> +
>> + if (RTE_ETH_DEV_SRIOV(dev).active != 0) {
>> + /* Check multi-queue mode.
>> + * To no break software we accept ETH_MQ_RX_NONE as
>> this might be used
>> + * to turn off VLAN filter.
>> + *
>> + * FIXME if support RSS together with VMDq & SRIOV
>> + */
>> + if (rx_mq_mode != ETH_MQ_RX_NONE &&
>> + (rx_mq_mode & ETH_MQ_RX_VMDQ_ONLY)
>> == 0) {
>> + PMD_INIT_LOG(WARNING, " SRIOV active, RX
>> mode %d is not supported."
>> + "Driver will behave as in %d mode as
>> fallback.",
>> + rx_mq_mode, ETH_MQ_RX_NONE);
>> + }
>> +
>> + /* TX mode is not used in in this driver so mode might be
>> ignored.*/
>> + if (tx_mq_mode != ETH_MQ_TX_VMDQ_ONLY) {
>> + /* SRIOV only works in VMDq enable mode */
>> + PMD_INIT_LOG(WARNING, "TX mode %d is not
>> supported in SRIOV. "
>> + "Driver will behave as in %d mode as
>> fallback.",
>> + tx_mq_mode,
>> ETH_MQ_TX_VMDQ_ONLY);
>> + }
>> + } else {
>> + /*
>> + * To no break software that set invalid mode, only display
>> warning if
>> + * invalid mode is used.
>> + */
>> + if ((rx_mq_mode & (ETH_MQ_RX_RSS_FLAG |
>> ETH_MQ_RX_VMDQ_FLAG))
>> + != rx_mq_mode) {
>> + PMD_INIT_LOG(WARNING, "RX mode %d is not
>> supported. Driver will "
>> + "behave as in %d mode as fallback.",
>> rx_mq_mode,
>> + rx_mq_mode &
>> (ETH_MQ_RX_RSS_FLAG | ETH_MQ_RX_VMDQ_FLAG));
>> + }
>> +
>> + if (tx_mq_mode != ETH_MQ_TX_NONE) {
>> + PMD_INIT_LOG(WARNING, "TX mode %d is not
>> supported."
>> + "Driver will behave as in %d mode as
>> fallback.",
>> + tx_mq_mode, ETH_MQ_TX_NONE);
>> + }
>> + }
>> +
>
> Better to have new function for these new codes.
>
>> PMD_INIT_FUNC_TRACE();
>> intr->flags |= E1000_FLAG_NEED_LINK_UPDATE;
>> PMD_INIT_FUNC_TRACE();
>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>> b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>> index 02b9cda..8e9da3b 100644
>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>> @@ -863,7 +863,8 @@ eth_ixgbe_dev_init(__attribute__((unused)) struct
>> eth_driver *eth_drv,
>> "Failed to allocate %u bytes needed to store "
>> "MAC addresses",
>> ETHER_ADDR_LEN * hw->mac.num_rar_entries);
>> - return -ENOMEM;
>> + diag = -ENOMEM;
>> + goto error;
>> }
>> /* Copy the permanent MAC address */
>> ether_addr_copy((struct ether_addr *) hw->mac.perm_addr, @@ -
>> 876,7 +877,8 @@ eth_ixgbe_dev_init(__attribute__((unused)) struct
>> eth_driver *eth_drv,
>> PMD_INIT_LOG(ERR,
>> "Failed to allocate %d bytes needed to store MAC
>> addresses",
>> ETHER_ADDR_LEN * IXGBE_VMDQ_NUM_UC_MAC);
>> - return -ENOMEM;
>> + diag = -ENOMEM;
>> + goto error;
>> }
>>
>> /* initialize the vfta */
>> @@ -886,7 +888,13 @@ eth_ixgbe_dev_init(__attribute__((unused)) struct
>> eth_driver *eth_drv,
>> memset(hwstrip, 0, sizeof(*hwstrip));
>>
>> /* initialize PF if max_vfs not zero */
>> - ixgbe_pf_host_init(eth_dev);
>> + diag = ixgbe_pf_host_init(eth_dev);
>> + if (diag < 0) {
>> + PMD_INIT_LOG(ERR,
>> + "Failed to allocate %d bytes needed to store MAC
>> addresses",
>> + ETHER_ADDR_LEN * IXGBE_VMDQ_NUM_UC_MAC);
>> + goto error;
>> + }
>>
>> ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT);
>> /* let hardware know driver is loaded */ @@ -918,6 +926,11 @@
>> eth_ixgbe_dev_init(__attribute__((unused)) struct eth_driver *eth_drv,
>> ixgbe_enable_intr(eth_dev);
>>
>> return 0;
>> +
>> +error:
>> + rte_free(eth_dev->data->hash_mac_addrs);
>> + rte_free(eth_dev->data->mac_addrs);
>> + return diag;
>> }
>>
>>
>> @@ -1434,7 +1447,93 @@ ixgbe_dev_configure(struct rte_eth_dev *dev)
>> struct ixgbe_interrupt *intr =
>> IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
>>
>> + struct rte_eth_conf *dev_conf = &dev->data->dev_conf;
>> + struct rte_eth_dev_info dev_info;
>> + int retval;
>> +
>> PMD_INIT_FUNC_TRACE();
>> + retval = ixgbe_pf_configure_mq_sriov(dev);
>
> Do we need a non-sriov version to configure mq mode?
> In ixgbe_pf_configure_mq_sriov, in the case of no vf,
> It will early return, then no chance to configure and check mq mode and queue
> number.
> Do I miss anything here?
Function in case of no vf function return 1 and if bellow will allow
non-SRIOV configuration.
>
>> + if (retval <= 0)
>> + return retval;
>> +
>> + uint16_t nb_rx_q = dev->data->nb_rx_queues;
>> + uint16_t nb_tx_q = dev->data->nb_rx_queues;
>
> Rx or tx here?
Yes, it should be tx.
>
>> +
>> + /* For DCB we need to obtain maximum number of queues
>> dinamically,
>> + * as this depends on max VF exported in PF. */
>> + if ((dev_conf->rxmode.mq_mode == ETH_MQ_RX_DCB) ||
>> + (dev_conf->txmode.mq_mode == ETH_MQ_TX_DCB)) {
>> + /* Use dev_infos_get field as this might be pointer to PF or
>> VF. */
>> + (*dev->dev_ops->dev_infos_get)(dev, &dev_info);
>> + }
>> +
>> + /* For vmdq+dcb mode check our configuration before we go further
>> */
>> + if (dev_conf->rxmode.mq_mode == ETH_MQ_RX_VMDQ_DCB) {
>> + const struct rte_eth_vmdq_dcb_conf *conf;
>> +
>> + if (nb_rx_q != ETH_VMDQ_DCB_NUM_QUEUES) {
>> + PMD_INIT_LOG(ERR, " VMDQ+DCB,
>> nb_rx_q != %d\n",
>> + ETH_VMDQ_DCB_NUM_QUEUES);
>> + return (-EINVAL);
>> + }
>> + conf = &(dev_conf->rx_adv_conf.vmdq_dcb_conf);
>> + if (conf->nb_queue_pools != ETH_16_POOLS &&
>> + conf->nb_queue_pools != ETH_32_POOLS) {
>> + PMD_INIT_LOG(ERR, " VMDQ+DCB selected, "
>> + "number of RX queue pools must
>> be %d or %d\n",
>> + ETH_16_POOLS, ETH_32_POOLS);
>> + return (-EINVAL);
>> + }
>> + } else if (dev_conf->rxmode.mq_mode == ETH_MQ_RX_DCB) {
>> + /* For DCB mode check out configuration before we go
>> further */
>> + const struct rte_eth_dcb_rx_conf *conf;
>> +
>> + if (nb_rx_q != dev_info.max_rx_queues) {
>> + PMD_INIT_LOG(ERR, " DCB, number of RX
>> queues != %d\n",
>> + ETH_DCB_NUM_QUEUES);
>> + return (-EINVAL);
>> + }
>> + conf = &(dev_conf->rx_adv_conf.dcb_rx_conf);
>> + if (conf->nb_tcs != ETH_4_TCS &&
>> + conf->nb_tcs != ETH_8_TCS) {
>> + PMD_INIT_LOG(ERR, " DCB, number of RX TC must
>> be %d or %d\n",
>> + ETH_4_TCS, ETH_8_TCS);
>> + return (-EINVAL);
>> + }
>> + }
>> +
>> + if (dev_conf->txmode.mq_mode == ETH_MQ_TX_VMDQ_DCB) {
>> + const struct rte_eth_vmdq_dcb_tx_conf *conf;
>> +
>> + if (nb_tx_q != ETH_VMDQ_DCB_NUM_QUEUES) {
>> + PMD_INIT_LOG(ERR, " VMDQ+DCB, number of TX
>> queues != %d\n",
>> + ETH_VMDQ_DCB_NUM_QUEUES);
>> + return (-EINVAL);
>> + }
>> + conf = &(dev_conf->tx_adv_conf.vmdq_dcb_tx_conf);
>> + if (conf->nb_queue_pools != ETH_16_POOLS &&
>> + conf->nb_queue_pools != ETH_32_POOLS) {
>> + PMD_INIT_LOG(ERR, " VMDQ+DCB selected, "
>> + "number of TX qqueue pools must
>> be %d or %d\n",
>> + ETH_16_POOLS, ETH_32_POOLS);
>> + return (-EINVAL);
>> + }
>> + } else if (dev_conf->txmode.mq_mode == ETH_MQ_TX_DCB) {
>> + const struct rte_eth_dcb_tx_conf *conf;
>> +
>> + if (nb_tx_q != dev_info.max_tx_queues) {
>> + PMD_INIT_LOG(ERR, " DCB, number of queues must
>> be %d\n",
>> + ETH_DCB_NUM_QUEUES);
>> + return (-EINVAL);
>> + }
>> + conf = &(dev_conf->tx_adv_conf.dcb_tx_conf);
>> + if (conf->nb_tcs != ETH_4_TCS &&
>> + conf->nb_tcs != ETH_8_TCS) {
>> + PMD_INIT_LOG(ERR, " DCB, number of TX TC must
>> be %d or %d\n",
>> + ETH_4_TCS, ETH_8_TCS);
>> + return (-EINVAL);
>> + }
>> + }
>
> Better to have a separate function for these new codes.
>
>>
>> /* set flag to update link status after init */
>> intr->flags |= IXGBE_FLAG_NEED_LINK_UPDATE; diff --git
>> a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>> b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>> index 1383194..e70a6e8 100644
>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>> @@ -348,11 +348,14 @@ void ixgbe_vlan_hw_strip_enable_all(struct
>> rte_eth_dev *dev);
>>
>> void ixgbe_vlan_hw_strip_disable_all(struct rte_eth_dev *dev);
>>
>> -void ixgbe_pf_host_init(struct rte_eth_dev *eth_dev);
>> +int ixgbe_pf_host_init(struct rte_eth_dev *eth_dev);
>>
>> void ixgbe_pf_mbx_process(struct rte_eth_dev *eth_dev);
>>
>> +int ixgbe_pf_configure_mq_sriov(struct rte_eth_dev *dev);
>> +
>> int ixgbe_pf_host_configure(struct rte_eth_dev *eth_dev);
>>
>> uint32_t ixgbe_convert_vm_rx_mask_to_val(uint16_t rx_mask, uint32_t
>> orig_val);
>> +
>> #endif /* _IXGBE_ETHDEV_H_ */
>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_pf.c
>> b/lib/librte_pmd_ixgbe/ixgbe_pf.c index 4103e97..a7b9333 100644
>> --- a/lib/librte_pmd_ixgbe/ixgbe_pf.c
>> +++ b/lib/librte_pmd_ixgbe/ixgbe_pf.c
>> @@ -91,7 +91,7 @@ ixgbe_mb_intr_setup(struct rte_eth_dev *dev)
>> return 0;
>> }
>>
>> -void ixgbe_pf_host_init(struct rte_eth_dev *eth_dev)
>> +int ixgbe_pf_host_init(struct rte_eth_dev *eth_dev)
>> {
>> struct ixgbe_vf_info **vfinfo =
>> IXGBE_DEV_PRIVATE_TO_P_VFDATA(eth_dev->data-
>>> dev_private);
>> @@ -101,39 +101,31 @@ void ixgbe_pf_host_init(struct rte_eth_dev
>> *eth_dev)
>> IXGBE_DEV_PRIVATE_TO_UTA(eth_dev->data->dev_private);
>> struct ixgbe_hw *hw =
>> IXGBE_DEV_PRIVATE_TO_HW(eth_dev->data->dev_private);
>> + int retval;
>> uint16_t vf_num;
>> - uint8_t nb_queue;
>>
>> PMD_INIT_FUNC_TRACE();
>>
>> - RTE_ETH_DEV_SRIOV(eth_dev).active = 0;
>> - if (0 == (vf_num = dev_num_vf(eth_dev)))
>> - return;
>> + /* Fill sriov structure using default configuration. */
>> + retval = ixgbe_pf_configure_mq_sriov(eth_dev);
>> + if (retval != 0) {
>> + if (retval < 0)
>> + PMD_INIT_LOG(ERR, " Setting up SRIOV with default
>> device "
>> + "configuration should not fail. This is
>> a
>> BUG.");
>> + return 0;
>> + }
>>
>> + vf_num = dev_num_vf(eth_dev);
>> *vfinfo = rte_zmalloc("vf_info", sizeof(struct ixgbe_vf_info) *
>> vf_num, 0);
>> - if (*vfinfo == NULL)
>> - rte_panic("Cannot allocate memory for private VF data\n");
>> + if (*vfinfo == NULL) {
>> + PMD_INIT_LOG(ERR, "Cannot allocate memory for private VF
>> data.");
>> + return (-ENOMEM);
>> + }
>>
>> memset(mirror_info,0,sizeof(struct ixgbe_mirror_info));
>> memset(uta_info,0,sizeof(struct ixgbe_uta_info));
>> hw->mac.mc_filter_type = 0;
>>
>> - if (vf_num >= ETH_32_POOLS) {
>> - nb_queue = 2;
>> - RTE_ETH_DEV_SRIOV(eth_dev).active = ETH_64_POOLS;
>> - } else if (vf_num >= ETH_16_POOLS) {
>> - nb_queue = 4;
>> - RTE_ETH_DEV_SRIOV(eth_dev).active = ETH_32_POOLS;
>> - } else {
>> - nb_queue = 8;
>> - RTE_ETH_DEV_SRIOV(eth_dev).active = ETH_16_POOLS;
>> - }
>> -
>> - RTE_ETH_DEV_SRIOV(eth_dev).nb_rx_q_per_pool = nb_queue;
>> - RTE_ETH_DEV_SRIOV(eth_dev).nb_tx_q_per_pool = nb_queue;
>> - RTE_ETH_DEV_SRIOV(eth_dev).def_vmdq_idx = vf_num;
>> - RTE_ETH_DEV_SRIOV(eth_dev).def_pool_q_idx =
>> (uint16_t)(vf_num * nb_queue);
>> -
>> ixgbe_vf_perm_addr_gen(eth_dev, vf_num);
>>
>> /* init_mailbox_params */
>> @@ -142,7 +134,169 @@ void ixgbe_pf_host_init(struct rte_eth_dev
>> *eth_dev)
>> /* set mb interrupt mask */
>> ixgbe_mb_intr_setup(eth_dev);
>>
>> - return;
>> + return 0;
>> +}
>> +
>> +
>> +/*
>> + * Function that make SRIOV configuration, based on device
>> +configuration,
>> + * number of requested queues and number of VF created.
>> + * Function returns:
>> + * 1 - SRIOV is not enabled (no VF created)
>> + * 0 - proper SRIOV configuration found.
>> + * -EINVAL - no suitable SRIOV configuration found.
>> + */
>> +int
>> +ixgbe_pf_configure_mq_sriov(struct rte_eth_dev *dev) {
>> + struct rte_eth_conf *dev_conf = &dev->data->dev_conf;
>> + struct rte_eth_dev_sriov *sriov = &RTE_ETH_DEV_SRIOV(dev);
>> + uint16_t vf_num;
>> +
>> + vf_num = dev_num_vf(dev);
>> + if (vf_num == 0) {
>> + memset(sriov, 0, sizeof(*sriov));
>> + return 1;
>> + }
>> +
>> + /* Check multi-queue mode. */
>> + if ((dev_conf->rxmode.mq_mode == ETH_MQ_RX_DCB) ||
>> + (dev_conf->rxmode.mq_mode == ETH_MQ_RX_DCB_RSS)
>> ||
>> + (dev_conf->txmode.mq_mode == ETH_MQ_TX_DCB)) {
>> + /* SRIOV only works in VMDq enable mode */
>> + PMD_INIT_LOG(ERR, " SRIOV active, "
>> + "invlaid VMDQ rx mode (%u) or tx (%u)
>> mode.",
>> + dev_conf->rxmode.mq_mode, dev_conf-
>>> txmode.mq_mode);
>> + return (-EINVAL);
>> + }
>> +
>> + switch (dev_conf->rxmode.mq_mode) {
>> + case ETH_MQ_RX_VMDQ_DCB:
>> + if (vf_num <= ETH_16_POOLS)
>> + sriov->nb_rx_q_per_pool = 8;
>> + else if (vf_num <= ETH_32_POOLS)
>> + sriov->nb_rx_q_per_pool = 4;
>> + else {
>> + PMD_INIT_LOG(ERR,
>> + "DCB (SRIOV active) - VF count (%d) must be
>> less or equal 32.",
>> + vf_num);
>> + return (-EINVAL);
>> + }
>> +
>> + if (dev->data->nb_rx_queues < sriov->nb_rx_q_per_pool) {
>> + PMD_INIT_LOG(WARNING,
>> + "DCB (SRIOV active) rx queues (%d) count is
>> not equal %d.",
>> + dev->data->nb_rx_queues,
>> + sriov->nb_rx_q_per_pool);
>> + }
>> + break;
>> + case ETH_MQ_RX_RSS:
>> + PMD_INIT_LOG(INFO, "RSS (SRIOV active), "
>> + "rx mq mode is changed from: mq_mode %u
>> into VMDQ mq_mode %u.",
>> + dev_conf->rxmode.mq_mode, dev->data-
>>> dev_conf.rxmode.mq_mode);
>> + dev->data->dev_conf.rxmode.mq_mode =
>> ETH_MQ_RX_VMDQ_RSS;
>> + /* falltrought */
>> + case ETH_MQ_RX_VMDQ_RSS:
>> + if (vf_num >= ETH_64_POOLS) {
>> + /* FIXME: Is vf_num > 64 realy supported by
>> hardware? */
>> + PMD_INIT_LOG(ERR, "RSS (SRIOV active), "
>> + "VFs num must be less or equal 64.");
>> + return (-EINVAL);
>> + } else if (vf_num >= ETH_32_POOLS) {
>> + if (dev->data->nb_rx_queues != 1 && dev->data-
>>> nb_rx_queues != 2) {
>> + PMD_INIT_LOG(ERR, "RSS (SRIOV active, VF
>> count >= 32),"
>> + "invalid rx queues count %d.
>> It must be 1 or 2.",
>> + dev->data->nb_rx_queues);
>> + return (-EINVAL);
>> + }
>> +
>> + sriov->nb_rx_q_per_pool = dev->data-
>>> nb_rx_queues;
>> + } else {
>> + /* FIXME: is VT(16) + RSS realy supported? */
>
> Yes, I think it supports.
>
>> + if (dev->data->nb_rx_queues != 4) {
>> + PMD_INIT_LOG(ERR, "RSS (SRIOV active, VFs
>> count < 32), "
>> + "invalid rx queues count %d.
>> It must be 4.",
>> + dev->data->nb_rx_queues);
>> + return (-EINVAL);
>> + }
>> +
>> + sriov->nb_rx_q_per_pool = 4;
>
> Better to use macro to replace the number, so does above.
>
>> + }
>> + break;
>> + default: /* ETH_MQ_RX_VMDQ_ONLY or ETH_MQ_RX_NONE */
>> + /* if nothing mq mode configure, use default scheme */
>> + if (dev->data->dev_conf.rxmode.mq_mode !=
>> ETH_MQ_RX_VMDQ_ONLY) {
>> + PMD_INIT_LOG(INFO, "Rx mq mode changed
>> from %u into VMDQ %u.",
>> + dev->data-
>>> dev_conf.rxmode.mq_mode, ETH_MQ_RX_VMDQ_ONLY);
>> +
>> + dev->data->dev_conf.rxmode.mq_mode =
>> ETH_MQ_RX_VMDQ_ONLY;
>> + }
>> +
>> + /* queue 0 of each pool is used. */
>> + sriov->nb_rx_q_per_pool = 1;
>> + break;
>> + }
>> +
>> + switch (dev_conf->txmode.mq_mode) {
>> + case ETH_MQ_TX_VMDQ_DCB: /* DCB VMDQ in SRIOV mode*/
>> + if (vf_num <= ETH_16_POOLS)
>> + sriov->nb_tx_q_per_pool = 8;
>> + else if (vf_num <= ETH_32_POOLS)
>> + sriov->nb_tx_q_per_pool = 4;
>> + else if (vf_num <= ETH_64_POOLS)
>> + sriov->nb_tx_q_per_pool = 1;
>> + else {
>> + PMD_INIT_LOG(ERR, "DCB (SRIOV active), "
>> + "VF count (%d) must be less or equal
>> 64.",
>> + vf_num);
>> + return (-EINVAL);
>> + }
>> + break;
>> + default: /* ETH_MQ_TX_VMDQ_ONLY or ETH_MQ_TX_NONE */
>> + /* if nothing mq mode configure, use default scheme */
>> + if (dev->data->dev_conf.txmode.mq_mode !=
>> ETH_MQ_TX_VMDQ_ONLY) {
>> + PMD_INIT_LOG(INFO, "Tx mq mode is changed
>> from %u into VMDQ %u.",
>> + dev->data-
>>> dev_conf.txmode.mq_mode, ETH_MQ_TX_VMDQ_ONLY);
>> +
>> + dev->data->dev_conf.txmode.mq_mode =
>> ETH_MQ_TX_VMDQ_ONLY;
>> + }
>> +
>> + /* queue 0 of each pool is used. */
>> + sriov->nb_tx_q_per_pool = 1;
>> + break;
>> + }
>> +
>> + sriov->def_vmdq_idx = vf_num;
>> +
>> + /*
>> + * Pools starts at 2xN, 4xN or 8xN
>> + */
>> + if (vf_num >= ETH_32_POOLS) {
>> + /* This must be vf_num <= ETH_64_POOLS */
>> + sriov->active = ETH_64_POOLS;
>> + sriov->def_pool_q_idx = vf_num * 2;
>> + } else if (vf_num >= ETH_16_POOLS) {
>> + sriov->active = ETH_32_POOLS;
>> + sriov->def_pool_q_idx = vf_num * 4;
>> + } else {
>> + sriov->active = ETH_16_POOLS;
>> + sriov->def_pool_q_idx = vf_num * 8;
>> + }
>> +
>> + /* Check if available queus count is not less than allocated.*/
>
> A typo: queus
>
>> + if (dev->data->nb_rx_queues > sriov->nb_rx_q_per_pool) {
>> + PMD_INIT_LOG(ERR, "SRIOV active, rx queue count must
>> less or equal %d.",
>> + sriov->nb_rx_q_per_pool);
>> + return (-EINVAL);
>> + }
>> +
>> + if (dev->data->nb_rx_queues > sriov->nb_tx_q_per_pool) {
>
> Replace nb_rx_queues with nb_tx_queues?
Yes, you are right.
>
>> + PMD_INIT_LOG(ERR, "SRIOV active, tx queue count must
>> less or equal %d.",
>> + sriov->nb_tx_q_per_pool);
>> + return (-EINVAL);
>> + }
>> +
>> + return 0;
>> }
>>
>> int ixgbe_pf_host_configure(struct rte_eth_dev *eth_dev)
>> --
>> 1.9.1
>
--
Pawel
