On Wed, Jun 16, 2021 at 10:57 AM Matthew Joyce <mfjoyce2...@gmail.com> wrote:
> Hi Dr. Joel, > > I tried that in newlib/libc and there were at least no errors. > (Nothing leading me to believe it was successful either!) > > However I still got the same error when I sudo make install. > (sparc-rtems-ranlib: command not found) (among others!) > The target should be sparc-rtems6 when you configure newlib. This should mean invoking the script like "./j-newlib sparc-rtems6" And the RTEMS tools should be in your PATH. type sparc-rtems6-gcc To be sure. --joel > > Thanks again! > > Sincerely, > > Matt > > > > On Wed, Jun 16, 2021 at 3:06 PM Joel Sherrill <j...@rtems.org> wrote: > > > > Does adding --no-recursive and running it only from the directory you > touched a build system file in help? > > > > It is regenerating a lot you don't want to touch anyway. > > > > --joel > > > > On Wed, Jun 16, 2021, 5:32 AM Matthew Joyce <mfjoyce2...@gmail.com> > wrote: > >> > >> Hi Eshan, > >> > >> Thanks very much for your follow up! Ok, I see now that if I go into > >> development/newlib/newlib-cygwin/newlib and run autoreconf -fvi with > >> the v2.69 using the PATH that Dr. Joel just showed, it starts to run. > >> It always eventually exits with an error though. (please see attached > >> .txt). I hope you can read that...I used the command "script" to > >> output everything to a text file. > >> > >> Do you have any idea where I might be going wrong? > >> > >> Thank you! > >> > >> Sincerely, > >> > >> Matt > >> > >> On Tue, Jun 15, 2021 at 8:23 PM Eshan Dhawan <eshandhawa...@gmail.com> > wrote: > >> > > >> > Hi matt > >> > It would work if run inside newlib instead of newlib-cygwin > >> > run command inside of ../newlib-cygwin/newlib > >> > instead of ../newlib-cygwin > >> > > >> > > >> > On Tue, Jun 15, 2021 at 10:59 PM Matthew Joyce <mfjoyce2...@gmail.com> > wrote: > >> >> > >> >> Ah, ok will do! Thank you for the tip. > >> >> > >> >> On Tue, Jun 15, 2021 at 7:17 PM Gedare Bloom <ged...@rtems.org> > wrote: > >> >> > > >> >> > Just a note, it's more efficient to capture your terminal dump > into a > >> >> > text file and attach that, rather than put a screenshot up. > >> >> > > >> >> > On Tue, Jun 15, 2021 at 11:14 AM Matthew Joyce < > mfjoyce2...@gmail.com> wrote: > >> >> > > > >> >> > > Hi Gentlemen, > >> >> > > > >> >> > > Thanks very much for your quick replies! > >> >> > > > >> >> > > I just tried both, but perhaps I'm misinterpreting your > suggestions. > >> >> > > (Could you please see the attached commands / errors!) > >> >> > > > >> >> > > Eshan, > >> >> > > > >> >> > > I did see that link, but it wasn't clear to me what the solution > was...Sorry! > >> >> > > > >> >> > > Sincerely, > >> >> > > > >> >> > > Matt > >> >> > > > >> >> > > On Tue, Jun 15, 2021 at 6:52 PM Eshan Dhawan < > eshandhawa...@gmail.com> wrote: > >> >> > > > > >> >> > > > Hi Matt, > >> >> > > > Try running the command with autoconf version 2.69 that's > shipped with RTEMS in the rtems bin > >> >> > > > That works as well. > >> >> > > > > >> >> > > > Also From a quick google search this is what I found : > https://superuser.com/questions/617872/cant-locate-autom4te-channeldefs-pm-in-inc-when-it-definitely-is-there > >> >> > > > > >> >> > > > On Tue, Jun 15, 2021 at 9:12 PM Matthew Joyce < > mfjoyce2...@gmail.com> wrote: > >> >> > > >> > >> >> > > >> Hello Dr. Joel and Eshan, > >> >> > > >> > >> >> > > >> I have a patch ready to send to Newlib for the sig function > prototypes > >> >> > > >> and STR2SIG_MAX. > >> >> > > >> > >> >> > > >> But to do that, I think I need to have Newlib built, which I > must > >> >> > > >> still be doing wrong. The error that I am getting is attached > below. > >> >> > > >> > >> >> > > >> I’ve been trying to follow the steps here: > >> >> > > >> > https://medium.com/my-gsoc-2019-journey/apply-newlib-patch-to-rtems-source-builder-6873b0fb31b8 > >> >> > > >> and > https://medium.com/my-gsoc-2019-journey/build-newlib-for-sparc-and-arm-architecture-6b3287d4c6f2 > >> >> > > >> > >> >> > > >> I even had rebuilt everything from scratch to see if that > would help, > >> >> > > >> but I still get the same error. Maybe I cloned the newlib > source into > >> >> > > >> the wrong directory? > >> >> > > >> > >> >> > > >> I was hoping to get the patch off to Newlib for review as a > first step > >> >> > > >> while I work on writing the actual methods. When you get a > moment, > >> >> > > >> could you please advise? Thank you very much! > >> >> > > >> > >> >> > > >> Sincerely, > >> >> > > >> > >> >> > > >> Matt > >> >> > > _______________________________________________ > >> >> > > devel mailing list > >> >> > > devel@rtems.org > >> >> > > http://lists.rtems.org/mailman/listinfo/devel >
_______________________________________________ devel mailing list devel@rtems.org http://lists.rtems.org/mailman/listinfo/devel