Hi Dr. Joel, I used the following, based on Vaibhav's blog:
$ export PATH=$HOME/development/rtems/6/bin:$PATH $ ../newlib-cygwin/configure --target=sparc-rtems6 --disable-shared --disable-nls --enable-werror --enable-newlib-supplied-syscalls --enable-interwork --enable-multilib --with-gnu-as --with-gnu-ld When I enter "type sparc-rtems6-gcc" (I hope I'm understanding that correctly!), I get sparc-rtems6-gcc is hashed...and then my PATH. Thanks again! V/r, Matt On Wed, Jun 16, 2021 at 6:06 PM Joel Sherrill <j...@rtems.org> wrote: > > > > On Wed, Jun 16, 2021 at 10:57 AM Matthew Joyce <mfjoyce2...@gmail.com> wrote: >> >> Hi Dr. Joel, >> >> I tried that in newlib/libc and there were at least no errors. >> (Nothing leading me to believe it was successful either!) >> >> However I still got the same error when I sudo make install. >> (sparc-rtems-ranlib: command not found) (among others!) > > > The target should be sparc-rtems6 when you configure newlib. > This should mean invoking the script like "./j-newlib sparc-rtems6" > > > And the RTEMS tools should be in your PATH. > > type sparc-rtems6-gcc > > To be sure. > > --joel >> >> >> Thanks again! >> >> Sincerely, >> >> Matt >> >> >> >> On Wed, Jun 16, 2021 at 3:06 PM Joel Sherrill <j...@rtems.org> wrote: >> > >> > Does adding --no-recursive and running it only from the directory you >> > touched a build system file in help? >> > >> > It is regenerating a lot you don't want to touch anyway. >> > >> > --joel >> > >> > On Wed, Jun 16, 2021, 5:32 AM Matthew Joyce <mfjoyce2...@gmail.com> wrote: >> >> >> >> Hi Eshan, >> >> >> >> Thanks very much for your follow up! Ok, I see now that if I go into >> >> development/newlib/newlib-cygwin/newlib and run autoreconf -fvi with >> >> the v2.69 using the PATH that Dr. Joel just showed, it starts to run. >> >> It always eventually exits with an error though. (please see attached >> >> .txt). I hope you can read that...I used the command "script" to >> >> output everything to a text file. >> >> >> >> Do you have any idea where I might be going wrong? >> >> >> >> Thank you! >> >> >> >> Sincerely, >> >> >> >> Matt >> >> >> >> On Tue, Jun 15, 2021 at 8:23 PM Eshan Dhawan <eshandhawa...@gmail.com> >> >> wrote: >> >> > >> >> > Hi matt >> >> > It would work if run inside newlib instead of newlib-cygwin >> >> > run command inside of ../newlib-cygwin/newlib >> >> > instead of ../newlib-cygwin >> >> > >> >> > >> >> > On Tue, Jun 15, 2021 at 10:59 PM Matthew Joyce <mfjoyce2...@gmail.com> >> >> > wrote: >> >> >> >> >> >> Ah, ok will do! Thank you for the tip. >> >> >> >> >> >> On Tue, Jun 15, 2021 at 7:17 PM Gedare Bloom <ged...@rtems.org> wrote: >> >> >> > >> >> >> > Just a note, it's more efficient to capture your terminal dump into a >> >> >> > text file and attach that, rather than put a screenshot up. >> >> >> > >> >> >> > On Tue, Jun 15, 2021 at 11:14 AM Matthew Joyce >> >> >> > <mfjoyce2...@gmail.com> wrote: >> >> >> > > >> >> >> > > Hi Gentlemen, >> >> >> > > >> >> >> > > Thanks very much for your quick replies! >> >> >> > > >> >> >> > > I just tried both, but perhaps I'm misinterpreting your >> >> >> > > suggestions. >> >> >> > > (Could you please see the attached commands / errors!) >> >> >> > > >> >> >> > > Eshan, >> >> >> > > >> >> >> > > I did see that link, but it wasn't clear to me what the solution >> >> >> > > was...Sorry! >> >> >> > > >> >> >> > > Sincerely, >> >> >> > > >> >> >> > > Matt >> >> >> > > >> >> >> > > On Tue, Jun 15, 2021 at 6:52 PM Eshan Dhawan >> >> >> > > <eshandhawa...@gmail.com> wrote: >> >> >> > > > >> >> >> > > > Hi Matt, >> >> >> > > > Try running the command with autoconf version 2.69 that's >> >> >> > > > shipped with RTEMS in the rtems bin >> >> >> > > > That works as well. >> >> >> > > > >> >> >> > > > Also From a quick google search this is what I found : >> >> >> > > > https://superuser.com/questions/617872/cant-locate-autom4te-channeldefs-pm-in-inc-when-it-definitely-is-there >> >> >> > > > >> >> >> > > > On Tue, Jun 15, 2021 at 9:12 PM Matthew Joyce >> >> >> > > > <mfjoyce2...@gmail.com> wrote: >> >> >> > > >> >> >> >> > > >> Hello Dr. Joel and Eshan, >> >> >> > > >> >> >> >> > > >> I have a patch ready to send to Newlib for the sig function >> >> >> > > >> prototypes >> >> >> > > >> and STR2SIG_MAX. >> >> >> > > >> >> >> >> > > >> But to do that, I think I need to have Newlib built, which I >> >> >> > > >> must >> >> >> > > >> still be doing wrong. The error that I am getting is attached >> >> >> > > >> below. >> >> >> > > >> >> >> >> > > >> I’ve been trying to follow the steps here: >> >> >> > > >> https://medium.com/my-gsoc-2019-journey/apply-newlib-patch-to-rtems-source-builder-6873b0fb31b8 >> >> >> > > >> and >> >> >> > > >> https://medium.com/my-gsoc-2019-journey/build-newlib-for-sparc-and-arm-architecture-6b3287d4c6f2 >> >> >> > > >> >> >> >> > > >> I even had rebuilt everything from scratch to see if that would >> >> >> > > >> help, >> >> >> > > >> but I still get the same error. Maybe I cloned the newlib >> >> >> > > >> source into >> >> >> > > >> the wrong directory? >> >> >> > > >> >> >> >> > > >> I was hoping to get the patch off to Newlib for review as a >> >> >> > > >> first step >> >> >> > > >> while I work on writing the actual methods. When you get a >> >> >> > > >> moment, >> >> >> > > >> could you please advise? Thank you very much! >> >> >> > > >> >> >> >> > > >> Sincerely, >> >> >> > > >> >> >> >> > > >> Matt >> >> >> > > _______________________________________________ >> >> >> > > devel mailing list >> >> >> > > devel@rtems.org >> >> >> > > http://lists.rtems.org/mailman/listinfo/devel _______________________________________________ devel mailing list devel@rtems.org http://lists.rtems.org/mailman/listinfo/devel