Instead of assigning the gpio range based on pdev->id, the patch makes changes to get the range from gpio core that is dynamically allocated.
As a result, the uses of pdev->id can be removed from the driver. This will make dt migration of the driver easier. Signed-off-by: Shawn Guo <[email protected]> Cc: Grant Likely <[email protected]> Cc: Sascha Hauer <[email protected]> --- arch/arm/plat-mxc/include/mach/gpio.h | 13 +++++++++---- arch/arm/plat-mxc/include/mach/irqs.h | 21 +++------------------ drivers/gpio/gpio-mxc.c | 18 ++++++++++-------- 3 files changed, 22 insertions(+), 30 deletions(-) diff --git a/arch/arm/plat-mxc/include/mach/gpio.h b/arch/arm/plat-mxc/include/mach/gpio.h index 31c820c..abdf5d7 100644 --- a/arch/arm/plat-mxc/include/mach/gpio.h +++ b/arch/arm/plat-mxc/include/mach/gpio.h @@ -23,10 +23,15 @@ #include <mach/hardware.h> #include <asm-generic/gpio.h> - -/* There's a off-by-one betweem the gpio bank number and the gpiochip */ -/* range e.g. GPIO_1_5 is gpio 5 under linux */ -#define IMX_GPIO_NR(bank, nr) (((bank) - 1) * 32 + (nr)) +/* + * There's a off-by-one betweem the gpio bank number and the gpiochip + * range e.g. GPIO_1_5 is gpio 5 under linux. + * + * When gpio core allocates gpio range for a bank, it starts from the + * end of the total range. That is to say, bank 0 will get a higher + * gpio range than bank 1. + */ +#define IMX_GPIO_NR(bank, nr) (ARCH_NR_GPIOS - (bank) * 32 + (nr)) /* use gpiolib dispatchers */ #define gpio_get_value __gpio_get_value diff --git a/arch/arm/plat-mxc/include/mach/irqs.h b/arch/arm/plat-mxc/include/mach/irqs.h index 35c89bc..00e812b 100644 --- a/arch/arm/plat-mxc/include/mach/irqs.h +++ b/arch/arm/plat-mxc/include/mach/irqs.h @@ -11,6 +11,8 @@ #ifndef __ASM_ARCH_MXC_IRQS_H__ #define __ASM_ARCH_MXC_IRQS_H__ +#include <asm-generic/gpio.h> + /* * SoCs with TZIC interrupt controller have 128 IRQs, those with AVIC have 64 */ @@ -22,30 +24,13 @@ #define MXC_GPIO_IRQ_START MXC_INTERNAL_IRQS -/* these are ordered by size to support multi-SoC kernels */ -#if defined CONFIG_SOC_IMX53 -#define MXC_GPIO_IRQS (32 * 7) -#elif defined CONFIG_ARCH_MX2 -#define MXC_GPIO_IRQS (32 * 6) -#elif defined CONFIG_SOC_IMX50 -#define MXC_GPIO_IRQS (32 * 6) -#elif defined CONFIG_ARCH_MX1 -#define MXC_GPIO_IRQS (32 * 4) -#elif defined CONFIG_ARCH_MX25 -#define MXC_GPIO_IRQS (32 * 4) -#elif defined CONFIG_SOC_IMX51 -#define MXC_GPIO_IRQS (32 * 4) -#elif defined CONFIG_ARCH_MX3 -#define MXC_GPIO_IRQS (32 * 3) -#endif - /* * The next 16 interrupts are for board specific purposes. Since * the kernel can only run on one machine at a time, we can re-use * these. If you need more, increase MXC_BOARD_IRQS, but keep it * within sensible limits. */ -#define MXC_BOARD_IRQ_START (MXC_INTERNAL_IRQS + MXC_GPIO_IRQS) +#define MXC_BOARD_IRQ_START (MXC_INTERNAL_IRQS + ARCH_NR_GPIOS) #ifdef CONFIG_MACH_MX31ADS_WM1133_EV1 #define MXC_BOARD_IRQS 80 diff --git a/drivers/gpio/gpio-mxc.c b/drivers/gpio/gpio-mxc.c index 2f6a81b..8241680 100644 --- a/drivers/gpio/gpio-mxc.c +++ b/drivers/gpio/gpio-mxc.c @@ -240,14 +240,13 @@ static int __devinit mxc_gpio_probe(struct platform_device *pdev) { struct mxc_gpio_port *port; struct resource *iores; + static int once = 0; int err; port = kzalloc(sizeof(struct mxc_gpio_port), GFP_KERNEL); if (!port) return -ENOMEM; - port->virtual_irq_start = MXC_GPIO_IRQ_START + pdev->id * 32; - iores = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!iores) { err = -ENODEV; @@ -277,14 +276,13 @@ static int __devinit mxc_gpio_probe(struct platform_device *pdev) writel(0, port->base + GPIO_IMR); writel(~0, port->base + GPIO_ISR); - /* gpio-mxc can be a generic irq chip */ - mxc_gpio_init_gc(port); - if (cpu_is_mx2()) { /* setup one handler for all GPIO interrupts */ - if (pdev->id == 0) + if (!once) { irq_set_chained_handler(port->irq, mx2_gpio_irq_handler); + once = 1; + } } else { /* setup one handler for each entry */ irq_set_chained_handler(port->irq, mx3_gpio_irq_handler); @@ -304,12 +302,16 @@ static int __devinit mxc_gpio_probe(struct platform_device *pdev) if (err) goto out_iounmap; - port->bgc.gc.base = pdev->id * 32; - err = gpiochip_add(&port->bgc.gc); if (err) goto out_bgpio_remove; + /* Here, we get a gpio number range/base assigned by gpio core */ + port->virtual_irq_start = MXC_GPIO_IRQ_START + port->bgc.gc.base; + + /* gpio-mxc can be a generic irq chip */ + mxc_gpio_init_gc(port); + list_add_tail(&port->node, &mxc_gpio_ports); return 0; -- 1.7.4.1 _______________________________________________ devicetree-discuss mailing list [email protected] https://lists.ozlabs.org/listinfo/devicetree-discuss
