On Sat, 2014-08-16 at 16:24 +0100, Daniel wrote:
> @Ivan: sorry about the double post.
>
> Am 11.08.2014 um 16:40 schrieb Ivan T. Ivanov <iiva...@mm-sol.com>:
> > diff --git a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
> > b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
> > new file mode 100644
> > index 0000000..994e748
> > --- /dev/null
> > +++ b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
> > @@ -0,0 +1,107 @@
> > +/*
> > + * This header provides constants for the Qualcomm PMIC gpio binding.
> > + */
> > +
> > +#ifndef _DT_BINDINGS_PINCTRL_QCOM_PMIC_GPIO_H
> > +#define _DT_BINDINGS_PINCTRL_QCOM_PMIC_GPIO_H
> > +
> > +#define PMIC_GPIO_PULL_UP_30 1
> > +#define PMIC_GPIO_PULL_UP_1P5 2
> > +#define PMIC_GPIO_PULL_UP_31P5 3
> > +#define PMIC_GPIO_PULL_UP_1P5_30 4
>
> Looking at drivers/pinctrl/qcom/pinctrl-ssbi-pmic.c, shouldn't these defines
> start at 0?
> e.g. #define PMIC_GPIO_PULL_UP_30 0
>
Initially "bias-pull-up" was used to set this parameter.
Zero value for "bias-pull-up" has special meaning "...the
pin is connected to VDD...". So values in DTS have to have
offset by one. Micro Amps are non-standard for pull-ups,
thats why I have changed this to "qcom,pull-up-strength", but I
have made mistake in config_set function. Following patch should
fix the issue. I will send updated version soon.
> However, I still cannot get any data from those 2 pins if I export them
> through /sys/class/gpio...
Ensure that you are exporting the right gpio number.
# cat /sys/kernel/debug/gpio
Will tell you correct gpio range for registered gpio chips.
>
> Device: Nexus 7 2013 WiFi
> Board: APQ8064
Thanks for testing this.
Regards,
Ivan
---
drivers/pinctrl/qcom/pinctrl-ssbi-pmic.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/pinctrl/qcom/pinctrl-ssbi-pmic.c
b/drivers/pinctrl/qcom/pinctrl-ssbi-pmic.c
index 9a1b443..dd424f4 100644
--- a/drivers/pinctrl/qcom/pinctrl-ssbi-pmic.c
+++ b/drivers/pinctrl/qcom/pinctrl-ssbi-pmic.c
@@ -446,7 +446,7 @@ static int pm8xxx_gpio_config_set(struct pinctrl_dev
*pctldev,
dev_err(pctrl->dev, "invalid pull-up level\n");
return -EINVAL;
}
- pin->bias = arg - PM8XXX_GPIO_BIAS_PU_30;
+ pin->bias = arg - PMIC_GPIO_PULL_UP_30;
banks |= BIT(2);
pin->disable = 0;
banks |= BIT(3);
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
