Hi, On Fri, Jun 30, 2017 at 08:22:13AM +1000, Jonathan Liu wrote: > Hi Maxime, > > On 30 June 2017 at 01:56, Maxime Ripard > <maxime.rip...@free-electrons.com> wrote: > > On Wed, Jun 28, 2017 at 08:39:33PM +1000, Jonathan Liu wrote: > >> >> + u32 int_status; > >> >> + u32 fifo_status; > >> >> + /* Read needs empty flag unset, write needs full flag unset */ > >> >> + u32 flag = read ? SUN4I_HDMI_DDC_FIFO_STATUS_EMPTY : > >> >> + SUN4I_HDMI_DDC_FIFO_STATUS_FULL; > >> >> + int ret; > >> >> + > >> >> + /* Wait until error or FIFO ready */ > >> >> + ret = readl_poll_timeout(hdmi->base + > >> >> SUN4I_HDMI_DDC_INT_STATUS_REG, > >> >> + int_status, > >> >> + is_err_status(int_status) || > >> >> + is_fifo_flag_unset(hdmi, &fifo_status, > >> >> flag), > >> >> + min(len, SUN4I_HDMI_DDC_FIFO_SIZE) * > >> >> byte_time, > >> >> + 100000); > >> >> + > >> >> + if (is_err_status(int_status)) > >> >> + return -EIO; > >> >> + if (ret) > >> >> + return -ETIMEDOUT; > >> > > >> > Why not just have > >> > ret = readl_poll_timeout(hdmi->base + SUN4I_HDMI_DDC_FIFO_STATUS_REG, > >> > reg, > >> > !(reg & flag), 100, 100000); > >> > > >> > if (ret < 0) > >> > if (is_err_status()) > >> > return -EIO; > >> > return ret; > >> > > >> > > >> > >> If I check error status after readl_poll_timeout and there is an error > >> (e.g. the I2C address does not have a corresponding device connected > >> or nothing connected to HDMI port) it will keep checking the fifo > >> status even though error bit is set in the int status and then timeout > >> after 100 ms. If it checks the int status register at the same time, > >> it will error after 100 nanoseconds. I don't want to introduce > >> unnecessary delays considering part of the reason for adding this > >> driver to make it more usable for non-standard use cases. > > > > Well, polling for 100ms doesn't seem great either. What was the > > rationale behind that timeout? > > > > When an error occurs one of the error bits will be set in the > INT_STATUS register so this is detected very quickly if I check the > INT_STATUS and FIFO_STATUS at the same time. The 100 ms timeout is in > case the I2C slave does clock stretching in which case the transfer > may take longer than the predicted time.
100ms isn't stretching anymore, it's worse than that. > > And we can also reverse the check and look at the INT_STATUS > > register. The errors will be there, and we can program the threshold > > we want in both directions and use the > > DDC_FIFO_Request_Interrupt_Status bit. > > > > I did try that when I was doing the v3 patch but I couldn't get it to > work as mentioned previously in the v3 patch discussion. I programmed > the FIFO_RX_TRIGGER_THRES and FIFO_TX_TRIGGER_THRES in DDC_FIFO_Ctrl > register at the same time as setting FIFO_Address_Clear but the > request interrupt status bit did not get updated to the appropriate > state that is consistent with the FIFO level and the thresholds. I did > try this several times for subsequent patch versions without success. What values did you set it to? Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel