Hi,
Il 22/03/2018 19:05, Maxime Ripard ha scritto:
On Wed, Mar 21, 2018 at 09:03:13PM +0100, Giulio Benetti wrote:
The A20-Linova1-7 HMI, also called Q027_2_F which is printed on production
label, is an industrial Human Machine Interface.
It features:
- 512MB DDR RAM
- 1 Sd-card >= 4GB
- 1 Usb otg(programmable via software) with A-Usb Connector
- 1 Usb host
- 1 Buzzer
- 1 Input for LiPo
- 1 Relay to signal absence of power supply
- 1 External Rtc with 56 bytes of ram + CR2032 battery
- 1 7" 24-bits Tft 800x480 with PCap on
- 1 Mono audio 1-watt amplifier
- 1 RS485 port
- 1 Power On Line through +12Vdc reaching 57.600baud,
from where it can be supplied and placed in a network of 50 units
- exposed jtag pins
HMI is supplied from +12Vdc.
Ethernet is absent, so for debugging, need to enable rndis on Usb otg
port through an A-A usb cable.
It comes in different flavours for connector types and can be found with
umounted features as requested by customers.
So this is essentially the same board than in patch 6, but with a
different screen?
You should have a single DT then, and handle the two different panels
using DT overlays.
Ok for having different DT overlays.
But do I have to submit them as patches? Or keep them in my company's repo?
I ask you this because this involves sending also patches for displays
and other little modifications to mainline ex:
- rgb888 pins
- 2 simple-panels
- 1 uart iomux pins
etc.
If I don't submit those overlays, the other patches wouldn't make sense
alone as I've seen, just like rgb888 pins.
Signed-off-by: Giulio Benetti <giulio.bene...@micronovasrl.com>
---
.../devicetree/bindings/arm/micronova.txt | 4 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun7i-a20-linova1-ctp-7i.dts | 192 +++++++++++++++++++++
3 files changed, 197 insertions(+)
create mode 100644 arch/arm/boot/dts/sun7i-a20-linova1-ctp-7i.dts
diff --git a/Documentation/devicetree/bindings/arm/micronova.txt
b/Documentation/devicetree/bindings/arm/micronova.txt
index 35c4127..9f5ac72 100644
--- a/Documentation/devicetree/bindings/arm/micronova.txt
+++ b/Documentation/devicetree/bindings/arm/micronova.txt
@@ -4,3 +4,7 @@ Micronova Device Tree Bindings
A20-LiNova1-4_3 HMI
Required root node properties:
- compatible = "micronova,a20-linova1-ctp-4_3i", "allwinner,sun7i-a20";
+
+A20-LiNova1-7 HMI
+Required root node properties:
+ - compatible = "micronova,a20-linova1-ctp-7i", "allwinner,sun7i-a20";
These bindings are unnecessary, but the panel-simple bindings should
be sent to the DT maintainers as well.
Ok, removed them and already sent the ones for display.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c45a4f25..eafa7cb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -942,6 +942,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-m3.dtb \
sun7i-a20-mk808c.dtb \
sun7i-a20-linova1-ctp-4_3i.dtb\
+ sun7i-a20-linova1-ctp-7i.dtb\
You should have a space after dtb, and it should be ordered
alphabetically.
Done.
sun7i-a20-olimex-som-evb.dtb \
sun7i-a20-olinuxino-lime.dtb \
sun7i-a20-olinuxino-lime2.dtb \
diff --git a/arch/arm/boot/dts/sun7i-a20-linova1-ctp-7i.dts
b/arch/arm/boot/dts/sun7i-a20-linova1-ctp-7i.dts
new file mode 100644
index 0000000..7fd0d98
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-linova1-ctp-7i.dts
@@ -0,0 +1,192 @@
+/*
+ * This is based on sun7i-a20-linova1-ctp-7i.dts
+ *
+ * Copyright 2014 - Hans de Goede <hdego...@redhat.com>
+ * Copyright (c) 2014 FUKAUMI Naoki <nao...@gmail.com>
+ * Copyright (c) 2018 Giulio Benetti <giulio.bene...@micronovasrl.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
You should use an SPDX license header here.
Done
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Micronova srl LiNova1 CTP 7i";
+ compatible = "micronova,a20-linova1-ctp-7i", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ panel: panel {
+ compatible = "cdtech,s070wv95-ct16", "simple-panel";
+ power-supply = <®_vcc3v3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_input: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_panel>;
+ };
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+
+ ft5x: touchscreen@38 {
+ compatible = "edt,edt-ft5206";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 2 IRQ_TYPE_EDGE_FALLING>; /* PH2 */
+ reset-gpios = <&pio 7 3 GPIO_ACTIVE_LOW>; /* PH3 */
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+®_usb0_vbus {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
Ideally you should be defining the regulators here too.
Added.
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
You're saying that this is a USB-A connector? Then it's not OTG since
it doesn't have an ID pin, this is an host.
Right, with a special overlay I will activate Usb Device for RNDIS,
so modified as host
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
+&be0 {
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
The nodes should be ordered by alphabetical order.
Done.
One last question:
now I have some patch already reviewed-by.
Do I have to re-submit entire patchset?
Thank you very much.
--
Giulio Benetti
CTO
MICRONOVA SRL
Sede: Via A. Niedda 3 - 35010 Vigonza (PD)
Tel. 049/8931563 - Fax 049/8931346
Cod.Fiscale - P.IVA 02663420285
Capitale Sociale € 26.000 i.v.
Iscritta al Reg. Imprese di Padova N. 02663420285
Numero R.E.A. 258642
Thanks!
Maxime
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
