Document the bindings used for the sn65dsi86 DSI to eDP bridge. Changes in v1: - Rephrase the dt-binding descriptions to be more inline with existing bindings (Andrzej Hajda). - Add missing dt-binding that are parsed by corresponding driver (Andrzej Hajda).
Changes in v2: - Remove edp panel specific dt-binding entries. Only keep bridge specific entries (Sean Paul). - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). Changes in v3: - Remove irq-gpio dt entry and instead populate is an interrupt property (Rob Herring). Changes in v4: - Add link to bridge chip datasheet (Stephen Boyd) - Add vpll and vcc regulator supply bindings (Stephen Boyd) - Add ref clk optional dt binding (Stephen Boyd) - Add gpio-controller optional dt binding (Stephen Boyd) Changes in v5: - Use clock property to specify the input refclk (Stephen Boyd). - Update gpio cell and pwm cell numbers (Stephen Boyd). Changes in v6: - Add property to mention the lane mapping scheme and polarity inversion (Stephen Boyd). Changes in v7: - Detail description of lane mapping scheme dt property (Andrzej Hajda/ Rob Herring). - Removed HDP gpio binding, since the bridge uses IRQ signal to determine HPD, and IRQ property is already documented in binding. Signed-off-by: Sandeep Panda <spa...@codeaurora.org> --- .../bindings/display/bridge/ti,sn65dsi86.txt | 109 +++++++++++++++++++++ 1 file changed, 109 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt new file mode 100644 index 0000000..33329f9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt @@ -0,0 +1,109 @@ +SN65DSI86 DSI to eDP bridge chip +-------------------------------- + +This is the binding for Texas Instruments SN65DSI86 bridge. +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf + +Required properties: +- compatible: Must be "ti,sn65dsi86" +- reg: i2c address of the chip, 0x2d as per datasheet +- enable-gpios: OF device-tree gpio specification for bridge_en pin (active high) + +- vccio-supply: A 1.8V supply that powers up the digital IOs. +- vpll-supply: A 1.8V supply that powers up the displayport PLL. +- vcca-supply: A 1.2V supply that powers up the analog circuits. +- vcc-supply: A 1.2V supply that powers up the digital core. + +Optional properties: +- interrupts: Specifier for the SN65DSI86 interrupt line. + +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID probing + +- gpio-controller: Marks the device has a GPIO controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../../gpio/gpio.txt for more information. +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of + the cell formats. + +- clock-names: should be "refclk" +- clocks: Specification for input reference clock. The reference + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. + +- lane-mapping: Specification to describe the logical to physical lane + mapping scheme and polarity inversion of eDP lanes on PCB. + Each pair present at index n (where n lies between 0 and 3) + describes the lane mapping of logical lane to physical lane n + and the polarity(it should be either 1 or 0) of the physical lane n. + + For example: + lane-mapping = <2 1>, + <1 0>, + <3 1>, + <0 0>; + + The above mapping describes that logical lane 2 is mapped to + physical lane 0 and polarity of physical lane 0 is inverted, + logical lane 1 is mapped to physical lane 1 and polarity of + physical lane 1 is normal, logical lane 3 is mapped to physical + lane 2 and polarity of physical lane 2 is inverted, logical lane 0 + is mapped to physical lane 4 and polarity of physical lane 3 is normal. + + If this property is not mentioned then it is assumed that physical + lanes 0 through 3 are mapped to logical lanes 0 through 3 and polarity + of all physical lanes is normal. + +Required nodes: +This device has two video ports. Their connections are modelled using the +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for DSI input +- Video port 1 for eDP output + +Example +------- + +edp-bridge@2d { + compatible = "ti,sn65dsi86"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2d>; + + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio3>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + + vccio-supply = <&pm8916_l17>; + vcca-supply = <&pm8916_l6>; + vpll-supply = <&pm8916_l17>; + vcc-supply = <&pm8916_l6>; + + clock-names = "refclk"; + clocks = <&input_refclk>; + + lane-mapping = <0 0>, /* Logical lane 0 is routed to physical lane 0 (!inv) */ + <1 1>, /* Logical lane 1 is routed to physical lane 1 (inv) */ + <2 0>, /* Logical lane 2 is routed to physical lane 2 (!inv) */ + <3 1>; /* Logical lane 3 is routed to physical lane 3 (inv) */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + edp_bridge_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + edp_bridge_out: endpoint { + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +} -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
