On Mon, 2020-12-21 at 12:26 -0700, Rob Herring wrote: > On Wed, Dec 16, 2020 at 05:30:11PM +0800, Chunfeng Yun wrote: > > Convert mediatek,mtu3.txt to YAML schema mediatek,mtu3.yaml > > > > Signed-off-by: Chunfeng Yun <chunfeng....@mediatek.com> > > --- > > v4: > > 1. refer to usb-drd.yaml insstead of usb/generic.txt > > the following ones suggested by Rob: > > 2. add the number of phys supported > > 3. fix indentation of wakeup > > 4. add examples for port and connector > > > > v3: > > 1. fix yamllint warning > > 2. remove pinctrl* properties > > 3. remove unnecessary '|' > > 4. drop unused labels in example > > > > v2: new patch > > --- > > .../devicetree/bindings/usb/mediatek,mtu3.txt | 108 ------- > > .../bindings/usb/mediatek,mtu3.yaml | 278 ++++++++++++++++++ > > 2 files changed, 278 insertions(+), 108 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.txt > > create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml > > [...] > > + > > + power-domains: > > + description: A phandle to USB power domain node to control USB's MTCMOS > > + maxItems: 1 > > + > > + clocks: > > + minItems: 1 > > + maxItems: 4 > > Don't need maxItems here. Ok, will remove it, and apply others > > > + items: > > + - description: Controller clock used by normal mode > > + - description: Reference clock used by low power mode etc > > + - description: Mcu bus clock for register access > > + - description: DMA bus clock for data transfer > > + > > + clock-names: > > + minItems: 1 > > + maxItems: 4 > > + items: > > + - const: sys_ck # required, the following ones are optional > > + - const: ref_ck > > + - const: mcu_ck > > + - const: dma_ck > > + > > + phys: > > + description: List of all the USB PHYs used > > + minItems: 0 > > + maxItems: 9 > > Need to define what each one is. Ok, will do it > > > + > > + vusb33-supply: > > + description: Regulator of USB AVDD3.3v > > + > > + vbus-supply: > > + deprecated: true > > + description: | > > + Regulator of USB VBUS5v, needed when supports dual-role mode. > > + Particularly, if use an output GPIO to control a VBUS regulator, > > should > > + model it as a regulator. See bindings/regulator/fixed-regulator.yaml > > + It's considered valid for compatibility reasons, not allowed for > > + new bindings, and put into a usb-connector node. > > + > > + dr_mode: > > + enum: [host, peripheral, otg] > > + default: otg > > + > > + maximum-speed: > > + enum: [super-speed-plus, super-speed, high-speed, full-speed] > > + > > + "#address-cells": > > + enum: [1, 2] > > + > > + "#size-cells": > > + enum: [1, 2] > > + > > + ranges: true > > + > > + extcon: > > + deprecated: true > > + description: | > > + Phandle to the extcon device detecting the IDDIG/VBUS state, neede > > + when supports dual-role mode. > > + It's considered valid for compatibility reasons, not allowed for > > + new bindings, and use "usb-role-switch" property instead. > > + > > + usb-role-switch: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: Support role switch. > > + type: boolean > > + > > + connector: > > + $ref: /connector/usb-connector.yaml# > > + description: > > + Connector for dual role switch, especially for "gpio-usb-b-connector" > > + type: object > > + > > + port: > > + description: > > + Any connector to the data bus of this controller should be modelled > > + using the OF graph bindings specified, if the "usb-role-switch" > > + property is used. See graph.txt > > + type: object > > + > > + enable-manual-drd: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: > > + supports manual dual-role switch via debugfs; usually used when > > + receptacle is TYPE-A and also wants to support dual-role mode. > > + type: boolean > > + > > + wakeup-source: > > + description: enable USB remote wakeup, see power/wakeup-source.txt > > + type: boolean > > + > > + mediatek,syscon-wakeup: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + maxItems: 1 > > + description: > > + A phandle to syscon used to access the register of the USB wakeup > > glue > > + layer between xHCI and SPM, the field should always be 3 cells long. > > + items: > > + items: > > + - description: > > + The first cell represents a phandle to syscon > > + - description: > > + The second cell represents the register base address of the > > glue > > + layer in syscon > > + - description: > > + The third cell represents the hardware version of the glue > > layer, > > + 1 is used by mt8173 etc, 2 is used by mt2712 etc > > + enum: [1, 2] > > + > > + mediatek,u3p-dis-msk: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: The mask to disable u3ports, bit0 for u3port0, > > + bit1 for u3port1, ... etc > > + > > +# Required child node when support dual-role > > +patternProperties: > > + "^usb@[0-9a-f]+$": > > + type: object > > + $ref: /usb/mediatek,mtk-xhci.yaml# > > + description: > > + The xhci should be added as subnode to mtu3 as shown in the following > > + example if the host mode is enabled. > > + > > +dependencies: > > + connector: [ 'usb-role-switch' ] > > + port: [ 'usb-role-switch' ] > > + wakeup-source: [ 'mediatek,syscon-wakeup' ] > > + > > +required: > > + - compatible > > + - reg > > + - reg-names > > + - interrupts > > + - clocks > > + - clock-names > > + > > +additionalProperties: false > > + > > +examples: > > + # Dual role switch by extcon > > + - | > > + #include <dt-bindings/clock/mt8173-clk.h> > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/interrupt-controller/irq.h> > > + #include <dt-bindings/phy/phy.h> > > + #include <dt-bindings/power/mt8173-power.h> > > + > > + usb@11271000 { > > + compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; > > + reg = <0x11271000 0x3000>, <0x11280700 0x0100>; > > + reg-names = "mac", "ippc"; > > + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; > > + phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>; > > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > > + clocks = <&topckgen CLK_TOP_USB30_SEL>; > > + clock-names = "sys_ck"; > > + vusb33-supply = <&mt6397_vusb_reg>; > > + vbus-supply = <&usb_p0_vbus>; > > + extcon = <&extcon_usb>; > > + dr_mode = "otg"; > > + wakeup-source; > > + mediatek,syscon-wakeup = <&pericfg 0x400 1>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + xhci: usb@11270000 { > > + compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; > > + reg = <0x11270000 0x1000>; > > + reg-names = "mac"; > > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > > + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; > > + clock-names = "sys_ck", "ref_ck"; > > + vusb33-supply = <&mt6397_vusb_reg>; > > + }; > > + }; > > + > > + # Enable/disable device by an input gpio for VBUS pin > > + - | > > + #include <dt-bindings/gpio/gpio.h> > > + #include <dt-bindings/power/mt2712-power.h> > > + > > + usb@112c1000 { > > + compatible = "mediatek,mt2712-mtu3", "mediatek,mtu3"; > > + reg = <0x112c1000 0x3000>, <0x112d0700 0x0100>; > > + reg-names = "mac", "ippc"; > > + interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_LOW>; > > + phys = <&u2port2 PHY_TYPE_USB2>; > > + power-domains = <&scpsys MT2712_POWER_DOMAIN_USB2>; > > + clocks = <&topckgen CLK_TOP_USB30_SEL>; > > + clock-names = "sys_ck"; > > + dr_mode = "peripheral"; > > + usb-role-switch; > > + > > + connector { > > + compatible = "gpio-usb-b-connector", "usb-b-connector"; > > + type = "micro"; > > + vbus-gpios = <&pio 13 GPIO_ACTIVE_HIGH>; > > + }; > > + }; > > + > > + # Dual role switch with type-c > > + - | > > + usb@11201000 { > > + compatible ="mediatek,mt8183-mtu3", "mediatek,mtu3"; > > + reg = <0x11201000 0x2e00>, <0x11203e00 0x0100>; > > + reg-names = "mac", "ippc"; > > + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>; > > + phys = <&u2port0 PHY_TYPE_USB2>; > > + clocks = <&clk26m>; > > + clock-names = "sys_ck"; > > + mediatek,syscon-wakeup = <&pericfg 0x400 1>; > > + wakeup-source; > > + dr_mode = "otg"; > > + usb-role-switch; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + host: usb@11200000 { > > + compatible = "mediatek,mt8183-xhci", "mediatek,mtk-xhci"; > > + reg = <0x11200000 0x1000>; > > + reg-names = "mac"; > > + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&clk26m>; > > + clock-names = "sys_ck"; > > + }; > > + > > + port { > > + usb_role_sw: endpoint { > > + remote-endpoint = <&hs_ep>; > > + }; > > + }; > > + }; > > + > > +... > > -- > > 2.18.0 > >
_______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel