Document new DVFS OPP table and power domain properties of the Host1x bus and devices sitting on the bus.
Reviewed-by: Rob Herring <r...@kernel.org> Signed-off-by: Dmitry Osipenko <dig...@gmail.com> --- .../display/tegra/nvidia,tegra20-host1x.txt | 49 +++++++++++++++++++ 1 file changed, 49 insertions(+) diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index 8a6d3e1ee306..62861a8fb5c6 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -20,6 +20,18 @@ Required properties: - reset-names: Must include the following entries: - host1x +Optional properties: +- operating-points-v2: See ../bindings/opp/opp.txt for details. + - power-domains: Phandle to HEG or core power domain. + +For each opp entry in 'operating-points-v2' table of host1x and its modules: +- opp-supported-hw: One bitfield indicating: + On Tegra20: SoC process ID mask + On Tegra30+: SoC speedo ID mask + + A bitwise AND is performed against the value and if any bit + matches, the OPP gets enabled. + Each host1x client module having to perform DMA through the Memory Controller should have the interconnect endpoints set to the Memory Client and External Memory respectively. @@ -45,6 +57,8 @@ of the following host1x client modules: - interconnect-names: Must include name of the interconnect path for each interconnect entry. Consult TRM documentation for information about available memory clients, see MEMORY CONTROLLER section. + - operating-points-v2: See ../bindings/opp/opp.txt for details. + - power-domains: Phandle to MPE power domain. - vi: video input @@ -128,6 +142,8 @@ of the following host1x client modules: - interconnect-names: Must include name of the interconnect path for each interconnect entry. Consult TRM documentation for information about available memory clients, see MEMORY CONTROLLER section. + - operating-points-v2: See ../bindings/opp/opp.txt for details. + - power-domains: Phandle to VENC power domain. - epp: encoder pre-processor @@ -147,6 +163,8 @@ of the following host1x client modules: - interconnect-names: Must include name of the interconnect path for each interconnect entry. Consult TRM documentation for information about available memory clients, see MEMORY CONTROLLER section. + - operating-points-v2: See ../bindings/opp/opp.txt for details. + - power-domains: Phandle to HEG or core power domain. - isp: image signal processor @@ -166,6 +184,7 @@ of the following host1x client modules: - interconnect-names: Must include name of the interconnect path for each interconnect entry. Consult TRM documentation for information about available memory clients, see MEMORY CONTROLLER section. + - power-domains: Phandle to VENC or core power domain. - gr2d: 2D graphics engine @@ -185,6 +204,8 @@ of the following host1x client modules: - interconnect-names: Must include name of the interconnect path for each interconnect entry. Consult TRM documentation for information about available memory clients, see MEMORY CONTROLLER section. + - operating-points-v2: See ../bindings/opp/opp.txt for details. + - power-domains: Phandle to HEG or core power domain. - gr3d: 3D graphics engine @@ -209,6 +230,8 @@ of the following host1x client modules: - interconnect-names: Must include name of the interconnect path for each interconnect entry. Consult TRM documentation for information about available memory clients, see MEMORY CONTROLLER section. + - operating-points-v2: See ../bindings/opp/opp.txt for details. + - power-domains: Phandles to 3D or core power domain. - dc: display controller @@ -241,6 +264,8 @@ of the following host1x client modules: - interconnect-names: Must include name of the interconnect path for each interconnect entry. Consult TRM documentation for information about available memory clients, see MEMORY CONTROLLER section. + - operating-points-v2: See ../bindings/opp/opp.txt for details. + - power-domains: Phandle to core power domain. - hdmi: High Definition Multimedia Interface @@ -267,6 +292,7 @@ of the following host1x client modules: - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - nvidia,edid: supplies a binary EDID blob - nvidia,panel: phandle of a display panel + - operating-points-v2: See ../bindings/opp/opp.txt for details. - tvo: TV encoder output @@ -277,6 +303,10 @@ of the following host1x client modules: - clocks: Must contain one entry, for the module clock. See ../clocks/clock-bindings.txt for details. + Optional properties: + - operating-points-v2: See ../bindings/opp/opp.txt for details. + - power-domains: Phandle to core power domain. + - dsi: display serial interface Required properties: @@ -305,6 +335,7 @@ of the following host1x client modules: - nvidia,panel: phandle of a display panel - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang up with in order to support up to 8 data lanes + - operating-points-v2: See ../bindings/opp/opp.txt for details. - sor: serial output resource @@ -408,6 +439,8 @@ Example: clocks = <&tegra_car TEGRA20_CLK_HOST1X>; resets = <&tegra_car 28>; reset-names = "host1x"; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; #address-cells = <1>; #size-cells = <1>; @@ -421,6 +454,8 @@ Example: clocks = <&tegra_car TEGRA20_CLK_MPE>; resets = <&tegra_car 60>; reset-names = "mpe"; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; }; vi@54080000 { @@ -429,6 +464,7 @@ Example: interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; assigned-clocks = <&tegra_car TEGRA210_CLK_VI>; assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; + operating-points-v2 = <&dvfs_opp_table>; clocks = <&tegra_car TEGRA210_CLK_VI>; power-domains = <&pd_venc>; @@ -510,6 +546,8 @@ Example: clocks = <&tegra_car TEGRA20_CLK_EPP>; resets = <&tegra_car 19>; reset-names = "epp"; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; }; isp { @@ -528,6 +566,8 @@ Example: clocks = <&tegra_car TEGRA20_CLK_GR2D>; resets = <&tegra_car 21>; reset-names = "2d"; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; }; gr3d { @@ -536,6 +576,8 @@ Example: clocks = <&tegra_car TEGRA20_CLK_GR3D>; resets = <&tegra_car 24>; reset-names = "3d"; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; }; dc@54200000 { @@ -547,6 +589,8 @@ Example: clock-names = "dc", "parent"; resets = <&tegra_car 27>; reset-names = "dc"; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; interconnects = <&mc TEGRA20_MC_DISPLAY0A &emc>, <&mc TEGRA20_MC_DISPLAY0B &emc>, @@ -571,6 +615,8 @@ Example: clock-names = "dc", "parent"; resets = <&tegra_car 26>; reset-names = "dc"; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; interconnects = <&mc TEGRA20_MC_DISPLAY0AB &emc>, <&mc TEGRA20_MC_DISPLAY0BB &emc>, @@ -596,6 +642,7 @@ Example: resets = <&tegra_car 51>; reset-names = "hdmi"; status = "disabled"; + operating-points-v2 = <&dvfs_opp_table>; }; tvo { @@ -604,6 +651,7 @@ Example: interrupts = <0 76 0x04>; clocks = <&tegra_car TEGRA20_CLK_TVO>; status = "disabled"; + operating-points-v2 = <&dvfs_opp_table>; }; dsi { @@ -615,6 +663,7 @@ Example: resets = <&tegra_car 48>; reset-names = "dsi"; status = "disabled"; + operating-points-v2 = <&dvfs_opp_table>; }; }; -- 2.32.0